Page 1 of 1
Qwerty board on gps how to change to always on top
Posted: Wed Dec 09, 2020 5:28 pm
by Pacman1311
How can u change so its always ontop
Re: Qwerty board on gps how to change to always on top
Posted: Wed Dec 09, 2020 7:11 pm
by RossPat
Pacman1311 wrote: ↑Wed Dec 09, 2020 5:28 pm
How can u change so its always ontop
You can't, it will always change back to the default keyboard.
Re: Qwerty board on gps how to change to always on top
Posted: Wed Dec 16, 2020 2:24 pm
by l0ngba
Following
Re: Qwerty board on gps how to change to always on top
Posted: Wed Dec 16, 2020 4:43 pm
by Bala1
There was a time when Qwerty would stay on unless the battery is disconnected and you could type into the unit while driving.
At some point in time if you car had a sync update by Ford you would lose those two functions. My car has never had a sync update so I still have them.
As per a post on another thread, see below, Stuart can get you back Qwerty.
Post by saeb » Sun Aug 16, 2020 12:58 am
Pull it out, post it to me an Walah, default qwerty keyboard.
Re: Qwerty board on gps how to change to always on top
Posted: Mon Dec 28, 2020 8:22 pm
by saeb
Basically anything before 3.0 was ok, eg 2.2.
Re: Qwerty board on gps how to change to always on top
Posted: Wed Dec 30, 2020 4:41 pm
by PXXLTWA
I changed my language to English (Aus) and it stays that way
Re: Qwerty board on gps how to change to always on top
Posted: Wed Dec 30, 2020 5:49 pm
by RossPat
PXXLTWA wrote: ↑Wed Dec 30, 2020 4:41 pm
I changed my language to English (Aus) and it stays that way
That is normal but the Qwerty keyboard doesn't stay.
Re: Qwerty board on gps how to change to always on top
Posted: Thu Dec 31, 2020 12:52 am
by PXXLTWA
I don't have the latest version of Sync 3 so I have now gathered that it goes when you update the software?
speaking of which,
I have a ELM327 wifi reader and have Forscanlite on IOS, also have it on a PC.
Unsure how to find silent mode in any menus in the above Apps and also on PC, I can connect to the Sync 3 on PX2 XLT with tech pack and read a bunch of data but silent mode doesn't show up anywhere?
Re: Qwerty board on gps how to change to always on top
Posted: Thu Dec 31, 2020 9:48 am
by RossPat
PXXLTWA wrote: ↑Thu Dec 31, 2020 12:52 am
I don't have the latest version of Sync 3 so I have now gathered that it goes when you update the software?
speaking of which,
I have a ELM327 wifi reader and have Forscanlite on IOS, also have it on a PC.
Unsure how to find silent mode in any menus in the above Apps and also on PC, I can connect to the Sync 3 on PX2 XLT with tech pack and read a bunch of data but silent mode doesn't show up anywhere?
It is quite possible that your dongle can't read all the modules.
If you have a licensed copy of Forscan and a correct dongle it should work.
Re: Qwerty board on gps how to change to always on top
Posted: Thu Dec 31, 2020 12:02 pm
by PXXLTWA
I think you are correct. I’ve read a few posts now and seen screen shots and I definitely don’t have the BCM control menu at the top.
Re: Qwerty board on gps how to change to always on top
Posted: Thu Dec 31, 2020 1:04 pm
by RossPat
PXXLTWA wrote: ↑Thu Dec 31, 2020 12:02 pm
I think you are correct. I’ve read a few posts now and seen screen shots and I definitely don’t have the BCM control menu at the top.
You need the fully licensed Windows version of Forscan to make changes
https://forscan.org/download.html