Faults - Forscan
Posted: Tue Jul 30, 2019 9:01 pm
Hello,
Fired up forscan today after a while. Here's the DTCs I got:
Grateful if you can guide me through that list please:
===DTC P0480:13===
Code: P0480 - Fan 1 Control Circuit
Additional Fault Symptom:
- Circuit Open
Module: Powertrain Control Module===END DTC P0480:13===
===PCM DTC P2122:00-28===
Code: P2122 - Throttle/Pedal Position Sensor/Switch D Circuit Low
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Powertrain Control Module
Freeze Frame :
-GLOBTIM: 0 sec - Global real time
-TOTAL_DIST: 77498.0 km - Total Distance
-RUNTM: 0 sec - Time Since Engine Start
-CET: 0.0 Nm - Calculated Engine Torque
-EVAPSUP_DC: NO - Evap system
-CCMSUP_DC: YES - CCMON$I
-CCM_EVAL: Yes - Comprehensive Components Monitor Evaluated
-CATSUP_DC: NO - Catalyst
-AIRSUP_DC: YES - secondary air system supported
-SAIR_EVAL: Yes - Secondary Air System Evaluated
-HCATSUP_DC: NO - Heated Catalyst
-O2SHTR_EVAL: Yes - Heated Exhaust Oxygen Sensor Heater System Evaluated
-HTRSUP_DC: NO - oxygen sensor heater monitor supported
-MISFSUP_DC: NO - misfire monitor supported
-EVAP_EVAL: Yes - Evaporative System Monitor Evaluated
-CAT_EVAL: Yes - Catalyst Monitor Evaluated
-HCAT_EVAL: Yes - Heated Catalyst Monitor Evaluated
-EGR_EVAL: Yes - Exhaust Gas Recirculation System Evaluated
-EGRSUP_DC: YES - EGR system monitoring
-FUEL_SUP: YES - fuel system monitor supported
-FUEL_EVAL: Yes - Fuel System Monitor Evaluated
-MIL: Off - Malfunction Indicator Lamp
-MISF_EVAL: Yes - Misfire Monitor Evaluated
-O2SSUP_DC: NO - oxygen sensor monitor supported
-O2S_EVAL: Yes - Oxygen Sensor Monitor Evaluated
-LOAD: 0.00 % - Calculated Load Value
-ECT: 78 °C - Engine coolant temperature
-MAP: 100.0 kPa - Manifold absolute pressure sensor
-RPM: 0 rev/min - Engine Revolutions Per Minute
-VSS: 0.0 km/h - Vehicle Speed
-IAT: 29 °C - Intake Air Temperature
-MAF: 2.77 g/sec - Mass Air Flow
-EGR_PCT: 0.00 % - Commanded EGR
-BARO: 100.0 kPa - Barometric pressure
-VPWR: 12.82 Volt - Control Module Voltage
-AAT: 24 °C - Ambient Air Temperature
-APP_REL: 0.00 % - Accelerator Pedal Position Relative
-FRP_ABS: 870.0 kPa - Fuel Rail Pressure (Absolute)
===END PCM DTC P2122:00-28===
===PCM DTC P2127:00-28===
Code: P2127 - Throttle/Pedal Position Sensor/Switch E Circuit Low
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Powertrain Control Module
Freeze Frame :
-GLOBTIM: 0 sec - Global real time
-TOTAL_DIST: 77498.0 km - Total Distance
-RUNTM: 0 sec - Time Since Engine Start
-CET: 0.0 Nm - Calculated Engine Torque
-EVAPSUP_DC: NO - Evap system
-CCMSUP_DC: YES - CCMON$I
-CCM_EVAL: Yes - Comprehensive Components Monitor Evaluated
-CATSUP_DC: NO - Catalyst
-AIRSUP_DC: YES - secondary air system supported
-SAIR_EVAL: Yes - Secondary Air System Evaluated
-HCATSUP_DC: NO - Heated Catalyst
-O2SHTR_EVAL: Yes - Heated Exhaust Oxygen Sensor Heater System Evaluated
-HTRSUP_DC: NO - oxygen sensor heater monitor supported
-MISFSUP_DC: NO - misfire monitor supported
-EVAP_EVAL: Yes - Evaporative System Monitor Evaluated
-CAT_EVAL: Yes - Catalyst Monitor Evaluated
-HCAT_EVAL: Yes - Heated Catalyst Monitor Evaluated
-EGR_EVAL: Yes - Exhaust Gas Recirculation System Evaluated
-EGRSUP_DC: YES - EGR system monitoring
-FUEL_SUP: YES - fuel system monitor supported
-FUEL_EVAL: Yes - Fuel System Monitor Evaluated
-MIL: Off - Malfunction Indicator Lamp
-MISF_EVAL: Yes - Misfire Monitor Evaluated
-O2SSUP_DC: NO - oxygen sensor monitor supported
-O2S_EVAL: Yes - Oxygen Sensor Monitor Evaluated
-LOAD: 0.00 % - Calculated Load Value
-ECT: 78 °C - Engine coolant temperature
-MAP: 100.0 kPa - Manifold absolute pressure sensor
-RPM: 0 rev/min - Engine Revolutions Per Minute
-VSS: 0.0 km/h - Vehicle Speed
-IAT: 29 °C - Intake Air Temperature
-MAF: 2.77 g/sec - Mass Air Flow
-EGR_PCT: 0.00 % - Commanded EGR
-BARO: 100.0 kPa - Barometric pressure
-VPWR: 12.82 Volt - Control Module Voltage
-AAT: 24 °C - Ambient Air Temperature
-APP_REL: 0.00 % - Accelerator Pedal Position Relative
-FRP_ABS: 870.0 kPa - Fuel Rail Pressure (Absolute)
===END PCM DTC P2127:00-28===
===BdyCM DTC B124D:02-8A===
Code: B124D - Tyre Pressure Sensor
Additional Fault Symptom:
- General Signal Failure
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC
Module: Body Control Module
===END BdyCM DTC B124D:02-8A===
===BdyCM DTC B1182:00-8A===
Code: B1182 - Tyre Pressure Monitoring System
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC
Module: Body Control Module
===END BdyCM DTC B1182:00-8A===
===BdyCM DTC B1A79:15-48===
Code: B1A79 - Rear Fog Lamp
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Body Control Module
===END BdyCM DTC B1A79:15-48===
===BdyCM DTC B11DB:08-48===
Code: B11DB - Battery Monitoring Module A
Additional Fault Symptom:
- Bus Signal/Message Failures
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Body Control Module
===END BdyCM DTC B11DB:08-48===
===BdyCM DTC B109F:97-08===
Code: B109F - Intrusion Sensor Module
Additional Fault Symptom:
- Component Or System Operation Obstructed Or Blocked
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC B109F:97-08===
===FCIM DTC B11F0:15-08===
Code: B11F0 - Air Intake Damper Position Sensor
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
===IPC DTC U0100:00-08===
Code: U0100 - Lost Communication With ECM/PCM A
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Instrument Panel Control Module
===END IPC DTC U0100:00-08===
===IPC DTC U0138:00-48===
Code: U0138 - Lost Communication with All Terrain Control Module
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Instrument Panel Control Module
===END IPC DTC U0138:00-48===
Fired up forscan today after a while. Here's the DTCs I got:
Grateful if you can guide me through that list please:
===DTC P0480:13===
Code: P0480 - Fan 1 Control Circuit
Additional Fault Symptom:
- Circuit Open
Module: Powertrain Control Module===END DTC P0480:13===
===PCM DTC P2122:00-28===
Code: P2122 - Throttle/Pedal Position Sensor/Switch D Circuit Low
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Powertrain Control Module
Freeze Frame :
-GLOBTIM: 0 sec - Global real time
-TOTAL_DIST: 77498.0 km - Total Distance
-RUNTM: 0 sec - Time Since Engine Start
-CET: 0.0 Nm - Calculated Engine Torque
-EVAPSUP_DC: NO - Evap system
-CCMSUP_DC: YES - CCMON$I
-CCM_EVAL: Yes - Comprehensive Components Monitor Evaluated
-CATSUP_DC: NO - Catalyst
-AIRSUP_DC: YES - secondary air system supported
-SAIR_EVAL: Yes - Secondary Air System Evaluated
-HCATSUP_DC: NO - Heated Catalyst
-O2SHTR_EVAL: Yes - Heated Exhaust Oxygen Sensor Heater System Evaluated
-HTRSUP_DC: NO - oxygen sensor heater monitor supported
-MISFSUP_DC: NO - misfire monitor supported
-EVAP_EVAL: Yes - Evaporative System Monitor Evaluated
-CAT_EVAL: Yes - Catalyst Monitor Evaluated
-HCAT_EVAL: Yes - Heated Catalyst Monitor Evaluated
-EGR_EVAL: Yes - Exhaust Gas Recirculation System Evaluated
-EGRSUP_DC: YES - EGR system monitoring
-FUEL_SUP: YES - fuel system monitor supported
-FUEL_EVAL: Yes - Fuel System Monitor Evaluated
-MIL: Off - Malfunction Indicator Lamp
-MISF_EVAL: Yes - Misfire Monitor Evaluated
-O2SSUP_DC: NO - oxygen sensor monitor supported
-O2S_EVAL: Yes - Oxygen Sensor Monitor Evaluated
-LOAD: 0.00 % - Calculated Load Value
-ECT: 78 °C - Engine coolant temperature
-MAP: 100.0 kPa - Manifold absolute pressure sensor
-RPM: 0 rev/min - Engine Revolutions Per Minute
-VSS: 0.0 km/h - Vehicle Speed
-IAT: 29 °C - Intake Air Temperature
-MAF: 2.77 g/sec - Mass Air Flow
-EGR_PCT: 0.00 % - Commanded EGR
-BARO: 100.0 kPa - Barometric pressure
-VPWR: 12.82 Volt - Control Module Voltage
-AAT: 24 °C - Ambient Air Temperature
-APP_REL: 0.00 % - Accelerator Pedal Position Relative
-FRP_ABS: 870.0 kPa - Fuel Rail Pressure (Absolute)
===END PCM DTC P2122:00-28===
===PCM DTC P2127:00-28===
Code: P2127 - Throttle/Pedal Position Sensor/Switch E Circuit Low
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Powertrain Control Module
Freeze Frame :
-GLOBTIM: 0 sec - Global real time
-TOTAL_DIST: 77498.0 km - Total Distance
-RUNTM: 0 sec - Time Since Engine Start
-CET: 0.0 Nm - Calculated Engine Torque
-EVAPSUP_DC: NO - Evap system
-CCMSUP_DC: YES - CCMON$I
-CCM_EVAL: Yes - Comprehensive Components Monitor Evaluated
-CATSUP_DC: NO - Catalyst
-AIRSUP_DC: YES - secondary air system supported
-SAIR_EVAL: Yes - Secondary Air System Evaluated
-HCATSUP_DC: NO - Heated Catalyst
-O2SHTR_EVAL: Yes - Heated Exhaust Oxygen Sensor Heater System Evaluated
-HTRSUP_DC: NO - oxygen sensor heater monitor supported
-MISFSUP_DC: NO - misfire monitor supported
-EVAP_EVAL: Yes - Evaporative System Monitor Evaluated
-CAT_EVAL: Yes - Catalyst Monitor Evaluated
-HCAT_EVAL: Yes - Heated Catalyst Monitor Evaluated
-EGR_EVAL: Yes - Exhaust Gas Recirculation System Evaluated
-EGRSUP_DC: YES - EGR system monitoring
-FUEL_SUP: YES - fuel system monitor supported
-FUEL_EVAL: Yes - Fuel System Monitor Evaluated
-MIL: Off - Malfunction Indicator Lamp
-MISF_EVAL: Yes - Misfire Monitor Evaluated
-O2SSUP_DC: NO - oxygen sensor monitor supported
-O2S_EVAL: Yes - Oxygen Sensor Monitor Evaluated
-LOAD: 0.00 % - Calculated Load Value
-ECT: 78 °C - Engine coolant temperature
-MAP: 100.0 kPa - Manifold absolute pressure sensor
-RPM: 0 rev/min - Engine Revolutions Per Minute
-VSS: 0.0 km/h - Vehicle Speed
-IAT: 29 °C - Intake Air Temperature
-MAF: 2.77 g/sec - Mass Air Flow
-EGR_PCT: 0.00 % - Commanded EGR
-BARO: 100.0 kPa - Barometric pressure
-VPWR: 12.82 Volt - Control Module Voltage
-AAT: 24 °C - Ambient Air Temperature
-APP_REL: 0.00 % - Accelerator Pedal Position Relative
-FRP_ABS: 870.0 kPa - Fuel Rail Pressure (Absolute)
===END PCM DTC P2127:00-28===
===BdyCM DTC B124D:02-8A===
Code: B124D - Tyre Pressure Sensor
Additional Fault Symptom:
- General Signal Failure
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC
Module: Body Control Module
===END BdyCM DTC B124D:02-8A===
===BdyCM DTC B1182:00-8A===
Code: B1182 - Tyre Pressure Monitoring System
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC
Module: Body Control Module
===END BdyCM DTC B1182:00-8A===
===BdyCM DTC B1A79:15-48===
Code: B1A79 - Rear Fog Lamp
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Body Control Module
===END BdyCM DTC B1A79:15-48===
===BdyCM DTC B11DB:08-48===
Code: B11DB - Battery Monitoring Module A
Additional Fault Symptom:
- Bus Signal/Message Failures
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Body Control Module
===END BdyCM DTC B11DB:08-48===
===BdyCM DTC B109F:97-08===
Code: B109F - Intrusion Sensor Module
Additional Fault Symptom:
- Component Or System Operation Obstructed Or Blocked
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC B109F:97-08===
===FCIM DTC B11F0:15-08===
Code: B11F0 - Air Intake Damper Position Sensor
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
===IPC DTC U0100:00-08===
Code: U0100 - Lost Communication With ECM/PCM A
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Instrument Panel Control Module
===END IPC DTC U0100:00-08===
===IPC DTC U0138:00-48===
Code: U0138 - Lost Communication with All Terrain Control Module
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Instrument Panel Control Module
===END IPC DTC U0138:00-48===