Ranger Mods

huskydog wrote: ↑Tue May 08, 2018 6:09 pm Hi there. Wish I read this earlier today!
Ford recently updated my MY17 Ranger Sync3 v2.2 to V3.0. Since then I've lost the ability for keyboard input while moving.

As above I enabled 'keyboard input while in motion' but it automatically changes the country code to 'CS' which faults the navigation. Manually changing country code back to 'AS' reverts the 'keyboard in motion' to disable.

Any news with an as-built code for this feature?

Cheers
Peter

tanooki_suit wrote: ↑Sat May 12, 2018 8:03 pm Stewart et al - I tried the above change to type while driving (before I saw this thread) and also lost navigation. Got the navigation fault, country code = CS etc as well. However, changing it back to AS has not fixed the problem. Additionally, the arrangement of functions on the home page has changed; previously, the navigation occupied a large square on the upper left of the screen, and the audio occupied a slim rectangle on the upper right. Now they have switched (navigation in small rectangle on the right) and all I have is the compass, although it doesn't move. Any ideas what this could be?

huskydog wrote: ↑Tue May 08, 2018 8:27 pm Thanks Stewart
I tried the previous version enable code but it didn't work, just faulted my Nav.
I'll persist with voice command like u suggest till there's a fix. Wish I had more time to experiment myself!
Cheers
Peter

hosie9 wrote: ↑Wed Jun 13, 2018 11:25 am so just to confirm,
theres no need to use coding now?
everything can be done via the as built quick selection section in forscan?

i would like to find out what all the codes do mean though just for general information and knowledge.
is there somewhere i can get this code information for my ranger?

cheers steve

saeb wrote: ↑Wed Mar 21, 2018 6:50 pm Follow this guide and see if it sorts your issues.

Its nearly a certainty that you have a wrong value in another area of the APIM asbuilt.

1. Save the asbuilt file to the desktop
2. Open the APIM asbuilt editor
3. Press load all, load the file you just saved. You may need to change the drop down box for file type on the right from .abt to .ab
3. Press write all.
4. You now have your factory asbuilt loaded.
5. Press the stop button to end the APIM configuaration and exit Forscan
6. Do a hard reset on the Sync 3 unit
7. Open Forscan again and connect to the vehicle
5. Press the yellow triangle on the left menu and read and clear all fault codes.
6. Your DTC may or may not clear at this point.

AeolusRicky wrote: ↑Mon Jun 25, 2018 7:11 pm Hi Stewart,

Are there any non as-built options for the PX1 or an as-built spreadsheet available with code descriptions or similar?

Love your work with the site, very informative.

Cheers

saeb wrote: ↑Mon Jun 25, 2018 7:05 pm As per PM, yes. Let us know the outcome.

saeb wrote: ↑Wed Mar 21, 2018 6:50 pm Follow this guide and see if it sorts your issues.

Its nearly a certainty that you have a wrong value in another area of the APIM asbuilt.

1. Save the asbuilt file to the desktop
2. Open the APIM asbuilt editor
3. Press load all, load the file you just saved. You may need to change the drop down box for file type on the right from .abt to .ab
3. Press write all.
4. You now have your factory asbuilt loaded.
5. Press the stop button to end the APIM configuaration and exit Forscan
6. Do a hard reset on the Sync 3 unit
7. Open Forscan again and connect to the vehicle
5. Press the yellow triangle on the left menu and read and clear all fault codes.
6. Your DTC may or may not clear at this point.

If you still have a nav warning. # Note, this menu system is based on the new v3 update so some items may appear to look different or be in a different location but they are there.

1. Turn key to accessories.
2. Make sure the radio is turned on.

3. Press and hold the eject and forward seek buttons until the test tone comes up. Let it go through its process until it takes you to the menus.

20180321_182040_resized.jpg

4. Go to test settings

20180321_182044_resized.jpg

5. Scroll nearly to the bottom and you will see Remove navigation fault If it is greyed out like mine then there are no faults, if it is black lettering then there is a fault so press it.

20180321_182122_resized.jpg

6. Press the Navigation button on the Sync 3 unit and check the maps.

7. Do not play with the APIM asbuilt

Flashwatches wrote: ↑Sat Jun 30, 2018 5:13 am Just a couple of quick asbuilt questions,
1, is there a code for folding in wing mirrors when you lock the car and unfolding on unlock?
2, is there a code for closing any open windows when you lock?
3, is there a code for bringing on fog lights with highbeam lights? And adding an option for it in the settings menu so you can enable and un-enable it? Or am I asking too much
And last one
4, is it possible to show tyre pressures in the instrument display?

Thanks guys
Graeme

Sent from my SM-G950F using Tapatalk

saeb wrote:

Flashwatches wrote: ↑Sat Jun 30, 2018 5:13 am Just a couple of quick asbuilt questions,
1, is there a code for folding in wing mirrors when you lock the car and unfolding on unlock?
2, is there a code for closing any open windows when you lock?
3, is there a code for bringing on fog lights with highbeam lights? And adding an option for it in the settings menu so you can enable and un-enable it? Or am I asking too much
And last one
4, is it possible to show tyre pressures in the instrument display?

Thanks guys
Graeme

Sent from my SM-G950F using Tapatalk

1. No. It requires 3rd party modules.
2. No. It requires, modules, loom, switches etc.
3. No. No and yes.
4. No.

Sorry to be mister negative.