Page 1 of 1
Faults
Posted: Thu Nov 29, 2018 6:27 pm
by kavir
===APIM DTC U3000:04-08===
Code: U3000 - Control Module
Additional Fault Symptom:
- System Internal Failures
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Accessory Protocol Interface Module
===END APIM DTC U3000:04-08===
===PAM DTC None===
Successful DTC reading, no error codes found
Module: Parking Aid Module
===END PAM DTC None===
===BdyCM DTC B1D01:15-48===
Code: B1D01 - Right Low Beam
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Body Control Module
===END BdyCM DTC B1D01:15-48===
===BdyCM DTC B1D00:15-48===
Code: B1D00 - Left Low Beam
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Body Control Module
===END BdyCM DTC B1D00:15-48===
===BdyCM DTC B1D03:15-48===
Code: B1D03 - Right High Beam Circuit
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Body Control Module
===END BdyCM DTC B1D03:15-48===
===BdyCM DTC B1D02:15-48===
Code: B1D02 - Left High Beam Circuit
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Body Control Module
===END BdyCM DTC B1D02:15-48===
===BdyCM DTC B124B:15-0A===
Code: B124B - Left Daytime Running Light
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC B124B:15-0A===
===BdyCM DTC B124A:15-0A===
Code: B124A - Right Daytime Running Light
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC B124A:15-0A===
===BdyCM DTC B1A79:15-48===
Code: B1A79 - Rear Fog Lamp
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Body Control Module
===END BdyCM DTC B1A79:15-48===
Hello Guys, got my forscan usb module, and these are the errors which came through with the initial scan. Can you please enlighten me?
Things I've done with the ranger so far was to change the headlights to the mustang style ones. It was plug n play.
Thanks a lot.
Re: Faults
Posted: Fri Nov 30, 2018 9:16 pm
by kavir
Anybody guys?
Sent from my iPhone using Tapatalk
Re: Faults
Posted: Fri Nov 30, 2018 9:59 pm
by RossPat
The only person who can help you is Stewart.
He works 8 days a week and gets very busy, so you will need a little patience.
Re: Faults
Posted: Sat Dec 01, 2018 5:17 pm
by Fireguard
I'm no expert, but considering they're light faults, and you changed the lights, its probably just picked up an open circuit due to removing the headlight plugs as part of the install
Re: Faults
Posted: Sat Dec 01, 2018 5:36 pm
by RossPat
Fireguard wrote: ↑Sat Dec 01, 2018 5:17 pm
I'm no expert, but considering they're light faults, and you changed the lights, its probably just picked up an open circuit due to removing the headlight plugs as part of the install
My guess as well, maybe clear the codes and see what happens.
Re: Faults
Posted: Sun Dec 02, 2018 8:30 pm
by saeb
kavir wrote: ↑Fri Nov 30, 2018 9:16 pm
Anybody guys?
Sent from my iPhone using Tapatalk
Do the ALL lights work correctly at the moment?
If yes then I will give you a list of changes in Forscan, once you confirm.
Re: Faults
Posted: Sun Dec 02, 2018 10:30 pm
by kavir
saeb wrote: ↑Sun Dec 02, 2018 8:30 pm
kavir wrote: ↑Fri Nov 30, 2018 9:16 pm
Anybody guys?
Sent from my iPhone using Tapatalk
Do the ALL lights work correctly at the moment?
If yes then I will give you a list of changes in Forscan, once you confirm.
Yes, they all do.
Re: Faults
Posted: Sun Dec 02, 2018 11:01 pm
by saeb
Backup the BCM asbuilt for changing any values!
Change these values, keeping in mind x's are left with the existing values.
726-27-02 xxx0-xxxx-xxxx
726-46-01 xxx0-xxxx-xxxx
726-46-02 x0xx-xxxx-xxxx
726-47-01 x0xx-xxx0-xxxx
726-48-01 x0xx-xxx0-xxxx
726-48-02 xxxx-xxxx-x0xx
Write the changes, clear all fault codes and rescan for faults. Advise on results.
If you still have faults, paste them here and PM me your VIN.
Re: Faults
Posted: Wed Dec 05, 2018 6:03 pm
by kavir
Hello Stewart!
Thanks a lot for the codes. However these errors keep on showing. I sent you my VIN in a PM as well.
===BdyCM DTC B130F:14-08===
Code: B130F - Run Accessory Control
Additional Fault Symptom:
- Circuit Short To Ground Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC B130F:14-08===
===BdyCM DTC B124B:15-0A===
Code: B124B - Left Daytime Running Light
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC B124B:15-0A===
===BdyCM DTC B124A:15-0A===
Code: B124A - Right Daytime Running Light
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC B124A:15-0A===
Re: Faults
Posted: Wed Dec 05, 2018 6:09 pm
by kavir
I forgot to mention that I changed the tail lights as well. Stock it was one fog light & one backing light. Now it's both backing lights.
Re: Faults
Posted: Mon Dec 10, 2018 12:22 am
by saeb
kavir wrote: ↑Wed Dec 05, 2018 6:09 pm
I forgot to mention that I changed the tail lights as well. Stock it was one fog light & one backing light. Now it's both backing lights.
Thanks, I'm getting to the rest of them but have just had no time this week.
Meanwhile are all lights operational on the vehicle?
Re: Faults
Posted: Wed Dec 12, 2018 5:38 pm
by kavir
Yes, all lights are operational. But the faults keep on showing. No worries mate. Until you have time!
Re: Faults
Posted: Sun Dec 16, 2018 9:50 pm
by saeb
Note to self. Look at this, this week.
Re: Faults
Posted: Mon Dec 17, 2018 12:11 pm
by chrisv
Any update on this. ( 2018 build XLT Ranger )
I also get
Code: B1D00 - Left Low Beam
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Body Control Module
Code: B1D02 - Left High Beam Circuit
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Body Control Module
Also the code B12C2 - Puddle Lamp
I have an issue with the left low beam cutting out since upgrading to HID's, this can take anywhere between 10 minutes and 40 minutes.
I have tried to disable the "Bulb Out Front" but I now have an issue with forscan not working properly. Any changes I try to make I get an error
"Vehicle Configuration Incorrect - Service Procedure Interupted"
Re: Faults
Posted: Mon Dec 17, 2018 5:04 pm
by saeb
chrisv wrote: ↑Mon Dec 17, 2018 12:11 pm
Any update on this. ( 2018 build XLT Ranger )
I also get
Code: B1D00 - Left Low Beam
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Body Control Module
Code: B1D02 - Left High Beam Circuit
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Body Control Module
Also the code B12C2 - Puddle Lamp
I have an issue with the left low beam cutting out since upgrading to HID's, this can take anywhere between 10 minutes and 40 minutes.
I have tried to disable the "Bulb Out Front" but I now have an issue with forscan not working properly. Any changes I try to make I get an error
"Vehicle Configuration Incorrect - Service Procedure Interupted"
Low and High Beams
726-27-02 xxx0-xxxx-xxxx
726-46-01 xxx0-xxxx-xxxx
726-46-02 x0xx-xxxx-xxxx
I have already added the puddle lamp removal in the non-asbuilt BCM. "Puddle Lamp Circuit" Change the option and write.
If you cannot write it is because you are entering the wrong data or entering the data in the wrong area or module. What exactly are you entering?
Re: Faults
Posted: Mon Dec 17, 2018 5:25 pm
by saeb
kavir wrote: ↑Wed Dec 05, 2018 6:03 pm
Hello Stewart!
Thanks a lot for the codes. However these errors keep on showing. I sent you my VIN in a PM as well.
===BdyCM DTC B130F:14-08===
Code: B130F - Run Accessory Control
Additional Fault Symptom:
- Circuit Short To Ground Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC B130F:14-08===
===BdyCM DTC B124B:15-0A===
Code: B124B - Left Daytime Running Light
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC B124B:15-0A===
===BdyCM DTC B124A:15-0A===
Code: B124A - Right Daytime Running Light
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC B124A:15-0A===
Are these new lights using the DRL circuit, or is DRL just part of the new lights control box?
Try
726-61-02 xxx0-x0xx-xxxx
and let me know if the lights still operate correctly and what DTCs are left.
Re: Faults
Posted: Tue Dec 18, 2018 10:41 am
by chrisv
Hi Stewart,
I managed to fix the issues with Forscan, I read somewhere to make sure all accessories were off as any power drain can cause the error I was having. My radio and fan were on, and once disabled Forscan saved changes that I made without error.
I disabled the puddle lamps in the non as build data and also managed to disable the "Bulb Out Front" and cleared the DTC's. Will monitor and see what happens.
Not sure that this will fix the issue that I am having with the left low beam turning off after a period of time. Once I notice the low beam is off, it turns back on if I turn the headlight switch off and on. The amount of time before it cuts out varies.
I have swapped the ballast, no change, will try globe next but getting that globe out is a pain in the but as not much room on that side with the battery
Re: Faults
Posted: Tue Dec 18, 2018 7:56 pm
by saeb
chrisv wrote: ↑Tue Dec 18, 2018 10:41 am
Hi Stewart,
I managed to fix the issues with Forscan, I read somewhere to make sure all accessories were off as any power drain can cause the error I was having. My radio and fan were on, and once disabled Forscan saved changes that I made without error.
I disabled the puddle lamps in the non as build data and also managed to disable the "Bulb Out Front" and cleared the DTC's. Will monitor and see what happens.
Not sure that this will fix the issue that I am having with the left low beam turning off after a period of time. Once I notice the low beam is off, it turns back on if I turn the headlight switch off and on. The amount of time before it cuts out varies.
I have swapped the ballast, no change, will try globe next but getting that globe out is a pain in the but as not much room on that side with the battery
What adaptor are you using? You may be best to install this test build, 3rd post from the bottom at the moment for the link.
The changes should resolve your issues. Did you install relays to run the HIDS? If not I would. I have had these ballasts blow and when they do you could end up sending 25,000 volts through your BCM which would not be a happy day and another reason I use LED over HID.
So if you have just done plug and play, relay it up asap.
Re: Faults
Posted: Thu Dec 24, 2020 7:29 am
by Scott1234
Just used those codes mentioned above to sort my low beam faults. I have fitted px3 hids to my px2. I have used relays on the hips. Only problem I have now is day running light faults. Any help appreciated.
Re: Faults
Posted: Mon Dec 28, 2020 8:13 pm
by saeb
From memory putting PX3 into PX2 will use the parker light circuit unless you have moved the front parkers to the dedicated DRL circuit?