Hi Saeb,
Found this PID list on the 6R80 trans Service Manual. Is the TCC_OSC# (Output State Control of Torque Converter) a possible find for Ultraguage by any chance?
I'm a 2012 BT50.
Cheers.
Information: Following the announcement on October 23, 2023, this site has been archived as of July 1, 2024. For further details, visit this page.
TC Locked status PID in 6R80 Service Manual
-
- Junior Member
- Posts: 6
- Joined: Sun Oct 27, 2019 8:39 am
- Location: Melbourne
- Model Of Vehicle: MAZDA BT50
- Year Of Vehicle: 2012
- Been thanked: 2 times
- saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
Can do but you will have to remember what equals what.
1. Also keep in mind that it is what is being commanded by the ECU so may not be actual.
2. Don't assume that there will be data output, just because it is in a manual does not mean the PID will output data.
3. Also unsure if you will see an actual change as factory tunes never completely lock, it is variable across the whole load/rpm range.
We have to show this as raw data, be sure you copy everything exactly as per the image below. If you do not see 00 with ignition on then you have not copied it exactly.
00 = Normal Operation
01 = Forced Unlock
02 = Forced Lock
03 = Forced Fast Lock
1. Also keep in mind that it is what is being commanded by the ECU so may not be actual.
2. Don't assume that there will be data output, just because it is in a manual does not mean the PID will output data.
3. Also unsure if you will see an actual change as factory tunes never completely lock, it is variable across the whole load/rpm range.
We have to show this as raw data, be sure you copy everything exactly as per the image below. If you do not see 00 with ignition on then you have not copied it exactly.
00 = Normal Operation
01 = Forced Unlock
02 = Forced Lock
03 = Forced Fast Lock
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic
-
- Junior Member
- Posts: 6
- Joined: Sun Oct 27, 2019 8:39 am
- Location: Melbourne
- Model Of Vehicle: MAZDA BT50
- Year Of Vehicle: 2012
- Been thanked: 2 times
Thanks, Stewart.
I've had the transmission tuned and so the TC locks in all gears except 1st and 2nd so finally rid of all the slipping.
The TCC_OSC# is probably redundant for me now with the tune. As you say, what's commanded and what's going on are two different things.
Perhaps a more accurate indication of "what's going on" would be TC_SLIPACT (Torque Converter Slip Actual)?
Thanks for you all efforts.
I've had the transmission tuned and so the TC locks in all gears except 1st and 2nd so finally rid of all the slipping.
The TCC_OSC# is probably redundant for me now with the tune. As you say, what's commanded and what's going on are two different things.
Perhaps a more accurate indication of "what's going on" would be TC_SLIPACT (Torque Converter Slip Actual)?
Thanks for you all efforts.
- saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
I believe slip is already on the calc. viewtopic.php?t=6907
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic
- saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
A request may not be actual. You may use requested against actual to diagnose an issue.
Why not just use "Trans Measured Slip Across Torque Convertor" PID in the PID calculator? Which is Measured as engine speed minus turbine shaft speed.
These transmission do not just lock and unlock. There is always some slip and the lockup maps are variable across the load and rpm range.
Why not just use "Trans Measured Slip Across Torque Convertor" PID in the PID calculator? Which is Measured as engine speed minus turbine shaft speed.
These transmission do not just lock and unlock. There is always some slip and the lockup maps are variable across the load and rpm range.
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic