Hey all
Had a weird error when i was trying to save the BdyCM module. All I was doing was trying to save the config after turning off the tub puddle lamp (removed the rear sports bar) and it gives me some upload error.
Running Win10 using the usb dongle bought off the shop. PX2 DC Auto.
Information: Following the announcement on October 23, 2023, this site has been archived as of July 1, 2024. For further details, visit this page.
Weird error when trying to save
- saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
Is the ignition on?
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic
-
- Junior Member
- Posts: 13
- Joined: Wed Feb 07, 2018 5:21 pm
- Location: Brisbane
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2018
- Has thanked: 3 times
- Been thanked: 1 time
Yes mate, left on - however - I did notice that the radio and dash auto shutoff. Not sure if that matters?
I have successfully changed the start up screen splashback logo so I can do things just not what I'm looking at.
Unless I'm supposed to turn everything on, connect, log into specific module, go through and do what I want, cycle the ignition then perform write? Not sure
I have successfully changed the start up screen splashback logo so I can do things just not what I'm looking at.
Unless I'm supposed to turn everything on, connect, log into specific module, go through and do what I want, cycle the ignition then perform write? Not sure
White 2018 Ranger XLT - all stock
-
- New Member
- Posts: 2
- Joined: Wed Apr 28, 2021 7:53 pm
- Location: Perth
- Model Of Vehicle: EVEREST TREND UA
- Year Of Vehicle: 2021
- Forscan Dongle Type: ELM327 with switch
- Been thanked: 1 time
You don't also have a bluetooth dongle plugged in simultaneously by any chance? this prevented me from writing Tyre circumference in BdyCm
-
- Junior Member
- Posts: 13
- Joined: Wed Feb 07, 2018 5:21 pm
- Location: Brisbane
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2018
- Has thanked: 3 times
- Been thanked: 1 time
I do have a ultrascan installed in the 2nd plug at the back. I'll give it a go without that plugged in. Cheers.
White 2018 Ranger XLT - all stock
- saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
Good catch Griffo17..
Remove the second device when programming always.
Also if modules are shutting down it can be a sign of low battery state of charge. Although module will program down to 10.2 volts on the bench I do not recommend doing so.
Remove the second device when programming always.
Also if modules are shutting down it can be a sign of low battery state of charge. Although module will program down to 10.2 volts on the bench I do not recommend doing so.
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic