Hi,
I have installed an amplifier and audio processor into the car, when playing the system with engine running and doors open it works perfectly. Chimes, sensors all sound as normal. When you close all doors a sound is introduced even with the headunit at 0 and changes with engine RPM, its not alternators whine etc but fake engine noise.
Due to the amplified signals this noise is loud and really hammers the speakers. I took it to the dealers and they hooked up the car but couldn't find any options to disable the ANC. I've had suggestions to unplug the mics in the headliner, but would prefer to deactivate it. Does anyone know if Forscan has an option for this?
Thanks in advance
Information: Following the announcement on October 23, 2023, this site has been archived as of July 1, 2024. For further details, visit this page.
Disable ANC - Active Noise Cancelling
- saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
Diable ANC
Module ACM
727-01-01 xxxx-xAxx-xxxx enable ANC
or
727-01-01 xxxx-x8xx-xxxx disable ANC
Depending on what channel you have installed your amp, eg. off rear speakers then you may leave ANC enabled on the front but disabled on the rear.
If this is the case use the below change as required;
727-01-01 xxxx-xAxx-xxxx enable ANC
and
727-01-02 xxCC-xx CC = CC Value in below chart, only change CC.
Turn ignition off for 30 seconds then back on.
Module ACM
727-01-01 xxxx-xAxx-xxxx enable ANC
or
727-01-01 xxxx-x8xx-xxxx disable ANC
Depending on what channel you have installed your amp, eg. off rear speakers then you may leave ANC enabled on the front but disabled on the rear.
If this is the case use the below change as required;
727-01-01 xxxx-xAxx-xxxx enable ANC
and
727-01-02 xxCC-xx CC = CC Value in below chart, only change CC.
Front Left | Font Right | Rears | CC Value |
---|---|---|---|
Yes | Yes | Yes | 45 |
Yes | Yes | No | 44 |
Yes | No | Yes | 41 |
Yes | No | No | 40 |
No | Yes | Yes | 05 |
No | Yes | No | 04 |
No | No | Yes | 01 |
No | No | No | 00 |
Turn ignition off for 30 seconds then back on.
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic
-
- New Member
- Posts: 3
- Joined: Fri Oct 19, 2018 9:41 pm
- Location: Sydney
- Model Of Vehicle: RANGER WILDTRAK PX3
- Year Of Vehicle: 2018
- Forscan Dongle Type: SAEB Forscan Dongle WIN7
- Been thanked: 2 times
Hi Stewart,
This worked and ANC has been disabled, i really want thank you for your assistance. Greatly appreciated
This worked and ANC has been disabled, i really want thank you for your assistance. Greatly appreciated
PX3 Wildtrak 2.0L
- saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
-
- Junior Member
- Posts: 11
- Joined: Tue Apr 06, 2021 9:27 pm
- Location: Romania
- Model Of Vehicle: RANGER LIMITED PX2 SA BUILT
- Year Of Vehicle: 2018
Hi Stewart, do you know which versions of the Ranger do have ANC capabilities and if by default are enabled or disabled? I'm pretty sure mine does not have it enabled, I am still waiting for my ELM327 to show up and cannot yet check. I have a Sync3 and the car is the one from the signature, thank you very much.
2018 Ranger Black Edition Limited 2.2tdci 4x4 manual
- saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
You will know if you have ANC as it will have 3 x small 1 inch vent plastics in the headliner.
To this day no 3.2L Ranger has ANC. 2.0L only.
I have tested with my 3.2L after adding the required components and although it works the engine creates to much vibration and is not tuned to it so have turned it back off.
To this day no 3.2L Ranger has ANC. 2.0L only.
I have tested with my 3.2L after adding the required components and although it works the engine creates to much vibration and is not tuned to it so have turned it back off.
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic
-
- New Member
- Posts: 4
- Joined: Tue Aug 15, 2017 10:23 pm
- Location: Sydney
- Model Of Vehicle: EVEREST TITANIUM UA
- Year Of Vehicle: 2017
- Forscan Dongle Type: SAEB Forscan Dongle WIN10
Hey
Iv done something but not sure if it’s related
I “think” iv turned of noise canceling on the front left speaker where the sun was connected to but iv since lost the speaker but the sub is still working
Any idea if these are the correct setting
Iv done something but not sure if it’s related
I “think” iv turned of noise canceling on the front left speaker where the sun was connected to but iv since lost the speaker but the sub is still working
Any idea if these are the correct setting
- Attachments
-
- IMG_7759.jpeg (4.86 MiB) Viewed 76 times
- IMG_7759.jpeg (4.86 MiB) Viewed 76 times
Stock standard but ready to modify
- saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
So press the load factory AB down the bottom, then write all and start again.
If it does not fix it then you have a bad amp.
If it does not fix it then you have a bad amp.
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic