Hello,
Fired up forscan today after a while. Here's the DTCs I got:
Grateful if you can guide me through that list please:
===DTC P0480:13===
Code: P0480 - Fan 1 Control Circuit
Additional Fault Symptom:
- Circuit Open
Module: Powertrain Control Module===END DTC P0480:13===
===PCM DTC P2122:00-28===
Code: P2122 - Throttle/Pedal Position Sensor/Switch D Circuit Low
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Powertrain Control Module
Freeze Frame :
-GLOBTIM: 0 sec - Global real time
-TOTAL_DIST: 77498.0 km - Total Distance
-RUNTM: 0 sec - Time Since Engine Start
-CET: 0.0 Nm - Calculated Engine Torque
-EVAPSUP_DC: NO - Evap system
-CCMSUP_DC: YES - CCMON$I
-CCM_EVAL: Yes - Comprehensive Components Monitor Evaluated
-CATSUP_DC: NO - Catalyst
-AIRSUP_DC: YES - secondary air system supported
-SAIR_EVAL: Yes - Secondary Air System Evaluated
-HCATSUP_DC: NO - Heated Catalyst
-O2SHTR_EVAL: Yes - Heated Exhaust Oxygen Sensor Heater System Evaluated
-HTRSUP_DC: NO - oxygen sensor heater monitor supported
-MISFSUP_DC: NO - misfire monitor supported
-EVAP_EVAL: Yes - Evaporative System Monitor Evaluated
-CAT_EVAL: Yes - Catalyst Monitor Evaluated
-HCAT_EVAL: Yes - Heated Catalyst Monitor Evaluated
-EGR_EVAL: Yes - Exhaust Gas Recirculation System Evaluated
-EGRSUP_DC: YES - EGR system monitoring
-FUEL_SUP: YES - fuel system monitor supported
-FUEL_EVAL: Yes - Fuel System Monitor Evaluated
-MIL: Off - Malfunction Indicator Lamp
-MISF_EVAL: Yes - Misfire Monitor Evaluated
-O2SSUP_DC: NO - oxygen sensor monitor supported
-O2S_EVAL: Yes - Oxygen Sensor Monitor Evaluated
-LOAD: 0.00 % - Calculated Load Value
-ECT: 78 °C - Engine coolant temperature
-MAP: 100.0 kPa - Manifold absolute pressure sensor
-RPM: 0 rev/min - Engine Revolutions Per Minute
-VSS: 0.0 km/h - Vehicle Speed
-IAT: 29 °C - Intake Air Temperature
-MAF: 2.77 g/sec - Mass Air Flow
-EGR_PCT: 0.00 % - Commanded EGR
-BARO: 100.0 kPa - Barometric pressure
-VPWR: 12.82 Volt - Control Module Voltage
-AAT: 24 °C - Ambient Air Temperature
-APP_REL: 0.00 % - Accelerator Pedal Position Relative
-FRP_ABS: 870.0 kPa - Fuel Rail Pressure (Absolute)
===END PCM DTC P2122:00-28===
===PCM DTC P2127:00-28===
Code: P2127 - Throttle/Pedal Position Sensor/Switch E Circuit Low
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Powertrain Control Module
Freeze Frame :
-GLOBTIM: 0 sec - Global real time
-TOTAL_DIST: 77498.0 km - Total Distance
-RUNTM: 0 sec - Time Since Engine Start
-CET: 0.0 Nm - Calculated Engine Torque
-EVAPSUP_DC: NO - Evap system
-CCMSUP_DC: YES - CCMON$I
-CCM_EVAL: Yes - Comprehensive Components Monitor Evaluated
-CATSUP_DC: NO - Catalyst
-AIRSUP_DC: YES - secondary air system supported
-SAIR_EVAL: Yes - Secondary Air System Evaluated
-HCATSUP_DC: NO - Heated Catalyst
-O2SHTR_EVAL: Yes - Heated Exhaust Oxygen Sensor Heater System Evaluated
-HTRSUP_DC: NO - oxygen sensor heater monitor supported
-MISFSUP_DC: NO - misfire monitor supported
-EVAP_EVAL: Yes - Evaporative System Monitor Evaluated
-CAT_EVAL: Yes - Catalyst Monitor Evaluated
-HCAT_EVAL: Yes - Heated Catalyst Monitor Evaluated
-EGR_EVAL: Yes - Exhaust Gas Recirculation System Evaluated
-EGRSUP_DC: YES - EGR system monitoring
-FUEL_SUP: YES - fuel system monitor supported
-FUEL_EVAL: Yes - Fuel System Monitor Evaluated
-MIL: Off - Malfunction Indicator Lamp
-MISF_EVAL: Yes - Misfire Monitor Evaluated
-O2SSUP_DC: NO - oxygen sensor monitor supported
-O2S_EVAL: Yes - Oxygen Sensor Monitor Evaluated
-LOAD: 0.00 % - Calculated Load Value
-ECT: 78 °C - Engine coolant temperature
-MAP: 100.0 kPa - Manifold absolute pressure sensor
-RPM: 0 rev/min - Engine Revolutions Per Minute
-VSS: 0.0 km/h - Vehicle Speed
-IAT: 29 °C - Intake Air Temperature
-MAF: 2.77 g/sec - Mass Air Flow
-EGR_PCT: 0.00 % - Commanded EGR
-BARO: 100.0 kPa - Barometric pressure
-VPWR: 12.82 Volt - Control Module Voltage
-AAT: 24 °C - Ambient Air Temperature
-APP_REL: 0.00 % - Accelerator Pedal Position Relative
-FRP_ABS: 870.0 kPa - Fuel Rail Pressure (Absolute)
===END PCM DTC P2127:00-28===
===BdyCM DTC B124D:02-8A===
Code: B124D - Tyre Pressure Sensor
Additional Fault Symptom:
- General Signal Failure
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC
Module: Body Control Module
===END BdyCM DTC B124D:02-8A===
===BdyCM DTC B1182:00-8A===
Code: B1182 - Tyre Pressure Monitoring System
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC
Module: Body Control Module
===END BdyCM DTC B1182:00-8A===
===BdyCM DTC B1A79:15-48===
Code: B1A79 - Rear Fog Lamp
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Body Control Module
===END BdyCM DTC B1A79:15-48===
===BdyCM DTC B11DB:08-48===
Code: B11DB - Battery Monitoring Module A
Additional Fault Symptom:
- Bus Signal/Message Failures
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Body Control Module
===END BdyCM DTC B11DB:08-48===
===BdyCM DTC B109F:97-08===
Code: B109F - Intrusion Sensor Module
Additional Fault Symptom:
- Component Or System Operation Obstructed Or Blocked
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC B109F:97-08===
===FCIM DTC B11F0:15-08===
Code: B11F0 - Air Intake Damper Position Sensor
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
===IPC DTC U0100:00-08===
Code: U0100 - Lost Communication With ECM/PCM A
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Instrument Panel Control Module
===END IPC DTC U0100:00-08===
===IPC DTC U0138:00-48===
Code: U0138 - Lost Communication with All Terrain Control Module
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Instrument Panel Control Module
===END IPC DTC U0138:00-48===
Information: Following the announcement on October 23, 2023, this site has been archived as of July 1, 2024. For further details, visit this page.
Faults - Forscan
- saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
Could have been low or flat battery at some point.
If you have fitted an idrive then that could account for throttle but otherwise clear them all then check the next day and see what comes back.
If any it will be a smaller list and be only what is valid. 70% of vehicle I do have DTCs and it does not necessarily mean there is a fault with a component.
If you have fitted an idrive then that could account for throttle but otherwise clear them all then check the next day and see what comes back.
If any it will be a smaller list and be only what is valid. 70% of vehicle I do have DTCs and it does not necessarily mean there is a fault with a component.
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic
- saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
Oh and you said the dealer did some updates which would account for some of them.
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic
- rastik86
- Junior Member
- Posts: 6
- Joined: Sun Feb 13, 2022 11:59 am
- Location: Melbourne
- Model Of Vehicle: RANGER XLT PX3
- Year Of Vehicle: 2021
- Forscan Dongle Type: Other
- Has thanked: 2 times
Hey just got this on FORscan.
========
Code: U0140 - Lost Communication With Body Control Module
Status:
-Previously set DTC - not present at time of request
-malfunction indicator is off for this DTC
-test not complete
Module: Power Steering Control Module
========
I have changed the Auto Lock feature to on, attempted and reset the Nav In Motion to stock as built.
Any idea what it is?
Cheers
========
Code: U0140 - Lost Communication With Body Control Module
Status:
-Previously set DTC - not present at time of request
-malfunction indicator is off for this DTC
-test not complete
Module: Power Steering Control Module
========
I have changed the Auto Lock feature to on, attempted and reset the Nav In Motion to stock as built.
Any idea what it is?
Cheers
- Attachments
-
- Screen Shot 2022-02-13 at 1.25.45 pm.png (4.78 MiB) Viewed 126 times
- Screen Shot 2022-02-13 at 1.25.45 pm.png (4.78 MiB) Viewed 126 times
Ford Ranger FX4 - MY2021.75 - PX3 -
=ARB Summit Bar, Stedi spotties/LED bars, tray and lift off canopy,
Old Man Emu 2" lift w/600kg constant load leafs=
OBDLink EX+ adaptor, running FORscan through CrossOver on M1 MacBook Pro
=ARB Summit Bar, Stedi spotties/LED bars, tray and lift off canopy,
Old Man Emu 2" lift w/600kg constant load leafs=
OBDLink EX+ adaptor, running FORscan through CrossOver on M1 MacBook Pro
- saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
Reset the DTCs and it should clear.
Basically start playing with modules and they reset, during a reset then another module may lose communication.
There is no nav in motion on a Sync 3.
Basically start playing with modules and they reset, during a reset then another module may lose communication.
There is no nav in motion on a Sync 3.
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic