Page 2 of 3
Re: DPF Regen Gauge - PX3 only
Posted: Thu Nov 14, 2019 12:20 am
by blueshine
The DPF soot (pid from this forum) seems to agree with this display on my biturbo. The exhaust filter gauge on the display rounds down to increments of 5% whereas the DPS soot in ODBlink goes up 1% at a time, but otherwise they have the same number.
Re: DPF Regen Gauge - PX3 only
Posted: Fri Nov 15, 2019 9:17 am
by Brett_32i
I can pop around over weekend if you wanted to play directly.
Re: DPF Regen Gauge - PX3 only
Posted: Sat Nov 16, 2019 8:30 pm
by saeb
Brett_32i wrote: ↑Fri Nov 15, 2019 9:17 am
I can pop around over weekend if you wanted to play directly.
Soory mate was a bit busy playing with firmware today and fishing tomorrow.
Re: DPF Regen Gauge - PX3 only
Posted: Sun Nov 17, 2019 9:33 am
by Brett_32i
No stress, if you want to look for yourself just yell out
Re: DPF Regen Gauge - PX3 only
Posted: Sun Nov 17, 2019 1:20 pm
by zk876
This works on my wildtrak 2019 " XLT 720-07-02 x9xx-xxxx "
Re: DPF Regen Gauge - PX3 only
Posted: Tue Mar 03, 2020 8:45 pm
by 78luk
Doing a mates 2litre bi turbo Wildtrack. Would the Everest setting be the one to use because it has the same motor?
Everest 720-07-02 xBxx-xxxx
Re: DPF Regen Gauge - PX3 only
Posted: Tue Mar 03, 2020 9:54 pm
by blueshine
No it's the XLT value as posted earlier in the thread.
Re: DPF Regen Gauge - PX3 only
Posted: Tue Mar 10, 2020 8:02 pm
by Evert
Hi guys and gals. I tried this on my XLT PX3 Ranger, but it didn't work.
IPC asbuilt
720-07-02
factory setting was: 0260 40D2
I changed this to: 0960 40D2
I didn't get the DPF gauge and I also lost the intelligent 4wd display.
I just re-read the initial post again. Since my initial value was 2 and I add 8, I should change it to A. Correct?
Re: DPF Regen Gauge - PX3 only
Posted: Tue Mar 10, 2020 10:40 pm
by saeb
Your asbuilt is non standard as an a Ranger never came with I4WD gauge.
As per the instructions - "Take the initial value eg. 3 and in windows calc or other changed to programmer mode, select hex and add 8 to your start value, the new character is what you will use."
Hex 2 plus 8 = A and not 9
xAxx-xxxx
Re: DPF Regen Gauge - PX3 only
Posted: Wed Mar 11, 2020 7:22 am
by Evert
Thanks Stewart, I’ll try that tonight
Re: DPF Regen Gauge - PX3 only
Posted: Wed Mar 11, 2020 6:04 pm
by Evert
Worked, thanks mate
Re: DPF Regen Gauge - PX3 only
Posted: Tue Jul 28, 2020 9:12 pm
by teddy1981
saeb wrote: ↑Sun Oct 06, 2019 4:04 pm
DPF Regen Gauge - PX3 only
XL,XLS 720-07-02 x8xx-xxxx
XLT 720-07-02 x9xx-xxxx
Everest 720-07-02 xBxx-xxxx
If you want to confirm the change is correct.
Take the initial value eg. 3 and in windows calc or other changed to programmer mode, select hex and add 8 to your start value, the new character is what you will use.
Gauge can be found in Driver Assist/DPF Status
20191006_155751.jpg
I tried this one on my 2019 Everest ambiente and the DPF % appeared in right cluster but it throws up this error when ignition is turned on - "front camera not present. service required"
any ideas Stewart?
Re: DPF Regen Gauge - PX3 only
Posted: Thu Jul 30, 2020 12:44 pm
by saeb
You have made an incorrect change on your calculation. Send me your saved IPC abt and will fix.
Re: DPF Regen Gauge - PX3 only
Posted: Fri Jul 31, 2020 2:27 pm
by wrxmy99
Hi all
Did this on my 3.2 XLT today and had to use the XLS change not that XLT as listed as my initial value was 0000-4078 so I changed it to 0800-4078 as per the guidance to add 8 hex.
XL,XLS 720-07-02 x8xx-xxxx
XLT 720-07-02 x9xx-xxxx
Everest 720-07-02 xBxx-xxxx
Just an FYI. Maybe because mine is a very early PX3 XLT? Not sure. Anyway thanks for the additional note to check the +8. Works a treat.
Andy
Re: DPF Regen Gauge - PX3 only
Posted: Sat Aug 01, 2020 2:29 pm
by teddy1981
saeb wrote: ↑Thu Jul 30, 2020 12:44 pm
You have made an incorrect change on your calculation. Send me your saved IPC abt and will fix.
Hi Stewart
attached ipc.abt as requested.
Thanks for your help, much appreciated.
Cheers
ted thompson
Re: DPF Regen Gauge - PX3 only
Posted: Sat Aug 01, 2020 5:04 pm
by wrxmy99
Update:
Just noticed since doing this the clock on my left screen shows “--:--“.
Clock on the Sync 3 centre screen in functioning as normal.
Any ideas/link? Should that 8 actually be a 9?
Thanks
Andy
wrxmy99 wrote: ↑Fri Jul 31, 2020 2:27 pm
Hi all
Did this on my 3.2 XLT today and had to use the XLS change not that XLT as listed as my initial value was 0000-4078 so I changed it to 0800-4078 as per the guidance to add 8 hex.
XL,XLS 720-07-02 x8xx-xxxx
XLT 720-07-02 x9xx-xxxx
Everest 720-07-02 xBxx-xxxx
Just an FYI. Maybe because mine is a very early PX3 XLT? Not sure. Anyway thanks for the additional note to check the +8. Works a treat.
Andy
Re: DPF Regen Gauge - PX3 only
Posted: Sat Aug 01, 2020 6:57 pm
by saeb
wrxmy99 wrote: ↑Sat Aug 01, 2020 5:04 pm
Update:
Just noticed since doing this the clock on my left screen shows “--:--“.
Clock on the Sync 3 centre screen in functioning as normal.
Any ideas/link? Should that 8 actually be a 9?
Thanks
Andy
Andy
Change Sync 3 time up and down an hour.
Re: DPF Regen Gauge - PX3 only
Posted: Sat Aug 01, 2020 6:58 pm
by saeb
teddy1981 wrote: ↑Sat Aug 01, 2020 2:29 pm
saeb wrote: ↑Thu Jul 30, 2020 12:44 pm
You have made an incorrect change on your calculation. Send me your saved IPC abt and will fix.
Hi Stewart
attached ipc.abt as requested.
Thanks for your help, much appreciated.
Cheers
ted thompson
I have only made the one change to B, you had a 2 for some reason.
Re: DPF Regen Gauge - PX3 only
Posted: Sun Aug 02, 2020 9:51 pm
by wrxmy99
saeb wrote: ↑Sat Aug 01, 2020 6:57 pm
Change Sync 3 time up and down an hour.
#legend
Thanks mate. Worked a treat.
Just out of curiosity, anyone else’s XLT have an 0 as the original entry and have to use an 8 as per guidance for the XLS?
Cheers
Andy
Re: DPF Regen Gauge - PX3 only
Posted: Mon Aug 03, 2020 6:27 am
by saeb
Your vehicle most likely has different options enabled. That change will affect about 6 other options.
Re: DPF Regen Gauge - PX3 only
Posted: Wed Aug 05, 2020 12:20 pm
by teddy1981
saeb wrote: ↑Sat Aug 01, 2020 6:58 pm
teddy1981 wrote: ↑Sat Aug 01, 2020 2:29 pm
saeb wrote: ↑Thu Jul 30, 2020 12:44 pm
You have made an incorrect change on your calculation. Send me your saved IPC abt and will fix.
Hi Stewart
attached ipc.abt as requested.
Thanks for your help, much appreciated.
Cheers
ted thompson
I have only made the one change to B, you had a 2 for some reason.
ipc_0713556001596272130.ABT
Hi Stewart
For some reason this file won't load, throws up an error. I have restored previously from backup ABTs but this one won't play nice.
Regards Ted
Re: DPF Regen Gauge - PX3 only
Posted: Wed Aug 05, 2020 5:58 pm
by saeb
Are you using the latest version of Forscan?
Re: DPF Regen Gauge - PX3 only
Posted: Tue Aug 11, 2020 8:34 am
by oguncemir
Working my 19 ranger xlt , but my front camera enabled too and off road guage gone ,shows front camera eror after i disabled it no problem thanks
Re: DPF Regen Gauge - PX3 only
Posted: Wed Aug 12, 2020 11:06 pm
by saeb
teddy1981 wrote: ↑Wed Aug 05, 2020 12:20 pm
saeb wrote: ↑Sat Aug 01, 2020 6:58 pm
teddy1981 wrote: ↑Sat Aug 01, 2020 2:29 pm
Hi Stewart
attached ipc.abt as requested.
Thanks for your help, much appreciated.
Cheers
ted thompson
I have only made the one change to B, you had a 2 for some reason.
ipc_0713556001596272130.ABT
Hi Stewart
For some reason this file won't load, throws up an error. I have restored previously from backup ABTs but this one won't play nice.
Regards Ted
rename the extension to lower case .abt it should resolve.
Re: DPF Regen Gauge - PX3 only
Posted: Thu Aug 13, 2020 9:30 pm
by teddy1981
all good, just had to disable front camera ( i dont have one) to get rid of the error.