Need some help from the brains trust…
I’ve had some fault codes that I haven’t been able to clear for a while now, and assume it’s from me fiddling around with asbuilts…
Pic attachEd
And unfortunately I don’t have an saved profile to be able to load asbuilt before the issues arose.
Main ones that I need help with are
Bcm b115e - camera module - camera works but have lost active steering lines
TRM u2100 - initial config not complete - can’t figure this one out, has me stumped as only recently started to appear, and ford installed towbar etc years ago
IPC u0199
IPC u023a
Please help!
Thanks gents
Information: Following the announcement on October 23, 2023, this site has been archived as of July 1, 2024. For further details, visit this page.
DTCs won’t reset/clear
-
jackos_one
- New Member
- Posts: 4
- Joined: Sat Jul 11, 2020 5:22 am
- Location: new zealand
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: ELM327 with switch
- Has thanked: 1 time
- Attachments
-
- 7FABAB3A-7021-4BAB-961F-143CAB136259.jpeg (6.92 MiB) Viewed 132 times
- 7FABAB3A-7021-4BAB-961F-143CAB136259.jpeg (6.92 MiB) Viewed 132 times
2015 px2 ranger
-
saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
Go to asbuilt on APIM, BCM and IPC and load factory AB. Load and write all for each module, clear DTCs and start again.
Ignore the TRM, although it can be sorted there is no asbuilt as such anyway and can be ignored. One step at a time.
Ignore the TRM, although it can be sorted there is no asbuilt as such anyway and can be ignored. One step at a time.
- 2022-12-26 19_31_44-.png (27.97 KiB) Viewed 121 times
- 2022-12-26 19_31_44-.png (27.97 KiB) Viewed 121 times
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic
-
jackos_one
- New Member
- Posts: 4
- Joined: Sat Jul 11, 2020 5:22 am
- Location: new zealand
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: ELM327 with switch
- Has thanked: 1 time
Thanks Stewart, I loaded factory AB for BCM and APIM, however when I went to do IPC, a warning popped up saying “number of blocks in file of module doesn’t match…” continue yes/no.
Is it safe to click yes and continue?
Asking, as this didn’t happen with the other modules and wasn’t sure.
Look forward to your reply.
Happy new year!
Is it safe to click yes and continue?
Asking, as this didn’t happen with the other modules and wasn’t sure.
Look forward to your reply.
Happy new year!
- Attachments
-
- A020B2CA-3436-4781-A20B-5F2F35D44A6B.jpeg (4.02 MiB) Viewed 104 times
- A020B2CA-3436-4781-A20B-5F2F35D44A6B.jpeg (4.02 MiB) Viewed 104 times
2015 px2 ranger
-
saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
Will be fine, just load and write, you are just running old firmware is all.
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic
-
jackos_one
- New Member
- Posts: 4
- Joined: Sat Jul 11, 2020 5:22 am
- Location: new zealand
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: ELM327 with switch
- Has thanked: 1 time
Hi mate,
Thanks for your help with this, truely appreciated.
Am having trouble loading factory AB for IPC, warning box says “incompatible configuration” due to blocks 2 and 6 failing.
Any ideas?
Cheers
Thanks for your help with this, truely appreciated.
Am having trouble loading factory AB for IPC, warning box says “incompatible configuration” due to blocks 2 and 6 failing.
Any ideas?
Cheers
- Attachments
-
- F88C5391-3410-4B57-A8BF-9DCDF9B4A0E6.jpeg (7.03 MiB) Viewed 89 times
- F88C5391-3410-4B57-A8BF-9DCDF9B4A0E6.jpeg (7.03 MiB) Viewed 89 times
-
- 1DBE43D8-3F40-40E4-9734-6C90198A10FB.jpeg (4.53 MiB) Viewed 89 times
- 1DBE43D8-3F40-40E4-9734-6C90198A10FB.jpeg (4.53 MiB) Viewed 89 times
2015 px2 ranger
-
saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
Clear all DTCs and see if there are any.
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic
-
GenieMan
- Donator
- Posts: 61
- Joined: Thu Sep 29, 2022 10:09 pm
- Location: Australia
- Model Of Vehicle: RANGER XL PX2
- Year Of Vehicle: 2015
- Has thanked: 12 times
- Been thanked: 1 time
I am also getting code U2100, what do I need to change to clear?
===TRM DTC U2100:00-2F===
Code: U2100 - Initial Configuration Not Complete
Module: Trailer Module
I have an XL but installed the dual screen cluster so I assume missing somthing from the car that that the cluster came out of.
EDIT:
same for
===IPC DTC U023A:00-0A===
Code: U023A - Lost Communication With Image Processing Module A
Module: Instrument Panel Control Module
===TRM DTC U2100:00-2F===
Code: U2100 - Initial Configuration Not Complete
Module: Trailer Module
I have an XL but installed the dual screen cluster so I assume missing somthing from the car that that the cluster came out of.
EDIT:
same for
===IPC DTC U023A:00-0A===
Code: U023A - Lost Communication With Image Processing Module A
Module: Instrument Panel Control Module