Hi All,
I was hoping that someone might be able to help me identify a connector pin part number that I am having trouble identifying.
I have recently purchased a Trac Electronics Power Mirror and Window Module kit for my PX1 and now started the install. Unfortunately after removing the connector from the back of the Power Mirror Switch I have found that I only have 7 holes pinned out in the connector instead of the required 9, with the two missing wires being for the power fold. The connectors to the mirrors in the doors are fully pinned out.
I have been through the wiring diagrams and this specific connector does not have a FoMoCo part number listed like most other connectors. The only potential identifier I can see is "MS-AL-10F", which would make some sense as it is a 10 pin female connector. I suspect it might be a Molex connector but there are no identifiable markings.
Any assistance would be appreciated.
Thanks,
Duncan
Information: Following the announcement on October 23, 2023, this site has been archived as of July 1, 2024. For further details, visit this page.
Power Mirror Switch Connector Pins
-
- Junior Member
- Posts: 15
- Joined: Thu Dec 17, 2020 1:22 pm
- Location: Brisbane
- Model Of Vehicle: RANGER XL PX
- Year Of Vehicle: 2015
- Forscan Dongle Type: SAEB Forscan Dongle WIN7
- Has thanked: 5 times
- Been thanked: 2 times
- Attachments
-
- Mirror Connector.jpg (156.39 KiB) Viewed 125 times
- Mirror Connector.jpg (156.39 KiB) Viewed 125 times
-
- Mirror Switch Connector 1.jpg (52.17 KiB) Viewed 125 times
- Mirror Switch Connector 1.jpg (52.17 KiB) Viewed 125 times
-
- Mirror Switch Connector Pin 1 sml.jpg (57.64 KiB) Viewed 125 times
- Mirror Switch Connector Pin 1 sml.jpg (57.64 KiB) Viewed 125 times
-
- Mirror Switch Connector Pin 2 sml.jpg (73.89 KiB) Viewed 125 times
- Mirror Switch Connector Pin 2 sml.jpg (73.89 KiB) Viewed 125 times
-
- Mirror Switch Connector Pin 3 sml.jpg (128.92 KiB) Viewed 125 times
- Mirror Switch Connector Pin 3 sml.jpg (128.92 KiB) Viewed 125 times
-
- Mirror Switch Connector Pin 4 sml.jpg (88.77 KiB) Viewed 125 times
- Mirror Switch Connector Pin 4 sml.jpg (88.77 KiB) Viewed 125 times
2015 PX1 XL Supercab
2017 PX2 XLT Subercab
2017 PX2 XLT Subercab
- saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
So you replaced the mirrors? Would not have thought an XL PX1 would have the motors to retract the mirrors.
Where would you wire these missing to wires to?
Buy a couple of plugs off Trac with pins and you can populate and solder as many as you like.
Where would you wire these missing to wires to?
Buy a couple of plugs off Trac with pins and you can populate and solder as many as you like.
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic
-
- Junior Member
- Posts: 15
- Joined: Thu Dec 17, 2020 1:22 pm
- Location: Brisbane
- Model Of Vehicle: RANGER XL PX
- Year Of Vehicle: 2015
- Forscan Dongle Type: SAEB Forscan Dongle WIN7
- Has thanked: 5 times
- Been thanked: 2 times
Thanks for the reply Stewart. My Ranger is a real Frankenstein's Monster. It has basically been rebodied as a PX2 XLT before I bought it. Already has the PX2 Power Mirrors and the Power Mirror Switch with the folding button.
I contacted Trac before I posted this question to see if they had any pins or connectors for sale but unfortunately they didn't. I then asked if they could help me out with identifying the connectors or pins or supply part numbers so that I could source them myself but they were not keen to assist.
I was hoping the wiring diagrams might be the answer but again came upon a dead end. I know RS have a heap of pins on their website but without access to a physical store or someone with expertise it is a bit of a stab in the dark to find the right ones. I might have to start trawling the wreckers to get some loom sections.
I contacted Trac before I posted this question to see if they had any pins or connectors for sale but unfortunately they didn't. I then asked if they could help me out with identifying the connectors or pins or supply part numbers so that I could source them myself but they were not keen to assist.
I was hoping the wiring diagrams might be the answer but again came upon a dead end. I know RS have a heap of pins on their website but without access to a physical store or someone with expertise it is a bit of a stab in the dark to find the right ones. I might have to start trawling the wreckers to get some loom sections.
2015 PX1 XL Supercab
2017 PX2 XLT Subercab
2017 PX2 XLT Subercab
- saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
That would be the easiest. Go and cut a couple of plugs off.corollavator wrote: ↑Sun Feb 21, 2021 5:14 pm Thanks for the reply Stewart. My Ranger is a real Frankenstein's Monster. It has basically been rebodied as a PX2 XLT before I bought it. Already has the PX2 Power Mirrors and the Power Mirror Switch with the folding button.
I contacted Trac before I posted this question to see if they had any pins or connectors for sale but unfortunately they didn't. I then asked if they could help me out with identifying the connectors or pins or supply part numbers so that I could source them myself but they were not keen to assist.
I was hoping the wiring diagrams might be the answer but again came upon a dead end. I know RS have a heap of pins on their website but without access to a physical store or someone with expertise it is a bit of a stab in the dark to find the right ones. I might have to start trawling the wreckers to get some loom sections.
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic
-
- Junior Member
- Posts: 15
- Joined: Thu Dec 17, 2020 1:22 pm
- Location: Brisbane
- Model Of Vehicle: RANGER XL PX
- Year Of Vehicle: 2015
- Forscan Dongle Type: SAEB Forscan Dongle WIN7
- Has thanked: 5 times
- Been thanked: 2 times
Well after many (many) hours searching online first at images and then page after page on electrical manufactures and wholesalers websites I have found the connector information for the Power Mirror Switch on a PX1. Just in case this style of connector is used elsewhere on any of the Ranger series I thought I would share this info with the forum.
Manufacturer: TE Connectivity (AMP)
Style: MULTILOCK 070 Series Automotive Connector
Regards,
Duncan
Manufacturer: TE Connectivity (AMP)
Style: MULTILOCK 070 Series Automotive Connector
Regards,
Duncan
2015 PX1 XL Supercab
2017 PX2 XLT Subercab
2017 PX2 XLT Subercab
-
- Junior Member
- Posts: 15
- Joined: Thu Dec 17, 2020 1:22 pm
- Location: Brisbane
- Model Of Vehicle: RANGER XL PX
- Year Of Vehicle: 2015
- Forscan Dongle Type: SAEB Forscan Dongle WIN7
- Has thanked: 5 times
- Been thanked: 2 times
Sorry, I forgot to mention that both RS Components and Element14 have pins and connectors to suit available online.
2015 PX1 XL Supercab
2017 PX2 XLT Subercab
2017 PX2 XLT Subercab