Auto Door Locking + Folding Mirrors PX3

Wed Mar 18, 2020 7:36 pm

Auto lock will be in right hand cluster screen, settings/vehicle/locks - auto lock

Phillwehbe89 · Sun Sep 13, 2020 5:36 pm

hi i have a 20.75 wildtrak. Im having trouble with disabling auto start stop. Ive done it from the pcm but in the bcm im getting confuse because its says bms auto start system. Do i switch it off?

Sun Sep 13, 2020 10:18 pm

Don't do it in the PCM.

Do it in BCM only. In the filter box up the top type stop and it will show one I have put in that has IPC wording in brackets. Disable that one and that is all. Don't worry about the IPC.

Phillwehbe89 · Tue Sep 15, 2020 5:48 am

My mistake i put pcm instead of ipc in my message. So like in the photo should i disable the ( bms/ auto start stop system,) cheers

Tue Sep 15, 2020 4:15 pm

That should be fine.

Phillwehbe89 · Tue Sep 15, 2020 7:15 pm

Thanks Stewart ill try it out tomorrow and post it for other users. Cheers

Phillwehbe89 · Wed Sep 16, 2020 5:00 pm

Thanks Stewart ive done it and it works. Ive noticed the voltage stays at 14.3. Usually it goes down to around 12.5 after a minute after starting the car. Is it coz the bms swiches off with that disabling the auto start stop? And should i change the voltage in the settings?

Wed Sep 16, 2020 6:47 pm

Because you have disable the battery management system which control stop start. Alternator will not turn off now and supply full voltage at all times.

Phillwehbe89 · Sun Sep 27, 2020 5:10 pm

should i make any adjustments to the battery settings?

Sun Sep 27, 2020 6:58 pm

I don't believe any other changes will matter. Disabling start stop disable the battery monitoring system.

jlc123 · Sun Sep 27, 2020 8:22 pm

: 20200927_202133.jpg (333.23 KiB) Viewed 440 times

: 20200927_202133.jpg (333.23 KiB) Viewed 440 times

This worked for my MY20.75 wildtrak

petez69 · Mon Oct 05, 2020 4:47 pm

I contacted Ford Australia today regaring my PX3 XLS 2020.75 model. Appears it has been removed due to EU regulations. They couldnt tell me any more however this option has been removed, sounds like from the above posts the underlying code has also been removed.....sucks as I was keen to get this going.....

Fri Oct 09, 2020 1:51 am

petez69 wrote: ↑Mon Oct 05, 2020 4:47 pm I contacted Ford Australia today regaring my PX3 XLS 2020.75 model. Appears it has been removed due to EU regulations. They couldnt tell me any more however this option has been removed, sounds like from the above posts the underlying code has also been removed.....sucks as I was keen to get this going.....

What has been removed? Nothing has been removed.

cdvreede · Wed Nov 25, 2020 5:34 pm

Works like a dream on my 20.75 Trend. Was told by dealer that "this car doesn't have it" - now it does.

Thnx guys!!

Nicbic · Mon Dec 28, 2020 7:31 pm

saeb wrote: ↑Mon Dec 10, 2018 3:37 pm Thought that would be the case.

Auto Lock

Change;

BCM
726-15-01 to x1x1-x1x1-x1xx
726-21-01 to xxx1-xxxx-xxxx

and

IPC
720-01-01 to xxxF-xxxx-xxxx

Do an ignition cycle and it should be able to be changed.

Just ran this on my MY19 XLT and working perfectly,
Cheers Stewart

JaroosPL · Mon Feb 01, 2021 6:01 am

Great, I set it up as you wrote and everything works.
you got a cold beer from me.
Ford Ranger 2020 2.0BT

t4thfavor · Tue Feb 02, 2021 1:19 pm

In case you want to give your alternator a break, you can plug an LED nightlight or a phone charger into the AC outlet if you have that option on your model. (I'm in the US, and that fully disables Auto Start/Stop without any BCM changes)

geoffmc · Sat Feb 06, 2021 7:39 pm

Hi Stewart,

Thansk for your work and assistance with this. My OBD cable arrived this week and updaed via ForScan today and it worked like a charm!

cheers
Geoff

corollavator · Sun Feb 21, 2021 1:42 pm

Is anyone able to tell me if Auto Door Lock is possible on a PX1? When I ran Forscan for the first time it was already showing as enabled but the system does not function.

Thanks Duncan

Sun Feb 21, 2021 3:53 pm

corollavator wrote: ↑Sun Feb 21, 2021 1:42 pm Is anyone able to tell me if Auto Door Lock is possible on a PX1? When I ran Forscan for the first time it was already showing as enabled but the system does not function.

Thanks Duncan

Being an XL it would be doubtful.

Power1997 · Sat Dec 18, 2021 7:37 pm

Awesome! been fighting with ford Customer service and the dealer over the user manual having "äutolock", keep getting told not an option.
Plug in this cable, change the codes, and Autolock now available. Everest 2021.75

Thanks Saeb, now to play with other codes...

Scaffy · Fri Dec 24, 2021 8:02 am

Is there a non-asbuilt option to do this or must it be done via asbuilt?

Fri Dec 24, 2021 11:58 am

Scaffy wrote: ↑Fri Dec 24, 2021 8:02 am Is there a non-asbuilt option to do this or must it be done via asbuilt?

Never looked. Just use the asbuilt in the last post on the first page. Just do the BCM 726 options, IPC change is not required due to PX3 not having the menu in the cluster anyway.

Scaffy · Fri Dec 24, 2021 11:59 pm

saeb wrote: ↑Fri Dec 24, 2021 11:58 am
Scaffy wrote: ↑Fri Dec 24, 2021 8:02 am Is there a non-asbuilt option to do this or must it be done via asbuilt?
Never looked. Just use the asbuilt in the last post on the first page. Just do the BCM 726 options, IPC change is not required due to PX3 not having the menu in the cluster anyway.

Will do, thanks.

Scaffy · Sat Dec 25, 2021 1:08 pm

saeb wrote: ↑Fri Dec 24, 2021 11:58 am
Scaffy wrote: ↑Fri Dec 24, 2021 8:02 am Is there a non-asbuilt option to do this or must it be done via asbuilt?
Never looked. Just use the asbuilt in the last post on the first page. Just do the BCM 726 options, IPC change is not required due to PX3 not having the menu in the cluster anyway.

I've just done it and I have the menu in the cluster on the Everest. I enabled Auto lock in non asbuilt IPC and did the two asbuilt in BdyCM