Ranger Mods

I wired a non-oem camera to a sync 1 4" ford ranger xls (philippine market) via 4dtech cables.

On various forums I followed:
Changed fcdim and bcm. Run BCM lin - gives out a warning its non oem.

If i just turn on fcdim - no rear view camera error.

Anyone has a solution? TIA.

Sent from my EML-L29 using Tapatalk

I don't understand the question.

You are running a non OEM camera and get a warning it's non OEM? Makes sense to me.

The camera does not have a LIN connectionso you will never have lines.

What is the actual issue you are having?

saeb wrote:I don't understand the question.

You are running a non OEM camera and get a warning it's non OEM? Makes sense to me.

The camera does not have a LIN connectionso you will never have lines.

What is the actual issue you are having?

Issue:
7A5-01-01 changed value to 2 on xXxx xxxx xxxx - no camera
726-39-02 changed value to 1 on xxxx xXxx xxxx - still no camera with DTC error.

Sent from my EML-L29 using Tapatalk

keenwerkz wrote: ↑Mon Jan 06, 2020 7:59 am

saeb wrote:I don't understand the question.

You are running a non OEM camera and get a warning it's non OEM? Makes sense to me.

The camera does not have a LIN connectionso you will never have lines.

What is the actual issue you are having?

Issue:
7A5-01-01 changed value to 2 on xXxx xxxx xxxx - no camera
726-39-02 changed value to 1 on xxxx xXxx xxxx - still no camera with DTC error.

Sent from my EML-L29 using Tapatalk

7A5-01-01 changed value to 2 on xXxx xxxx xxxx - no camera - This is correct.
726-39-02 changed value to 1 on xxxx xXxx xxxx - still no camera with DTC error. - Don't believe you need it as the camera does not have LIN.

Do you get a blue screen in reverse?
Have you changed any other FCDIM settings?
Did you also try a FDCIM reset from the spanner menu?

saeb wrote:

keenwerkz wrote: ↑Mon Jan 06, 2020 7:59 am

saeb wrote:I don't understand the question.

You are running a non OEM camera and get a warning it's non OEM? Makes sense to me.

The camera does not have a LIN connectionso you will never have lines.

What is the actual issue you are having?

Issue:
7A5-01-01 changed value to 2 on xXxx xxxx xxxx - no camera
726-39-02 changed value to 1 on xxxx xXxx xxxx - still no camera with DTC error.

Sent from my EML-L29 using Tapatalk

7A5-01-01 changed value to 2 on xXxx xxxx xxxx - no camera - This is correct.
726-39-02 changed value to 1 on xxxx xXxx xxxx - still no camera with DTC error. - Don't believe you need it as the camera does not have LIN.

Do you get a blue screen in reverse?
Have you changed any other FCDIM settings?
Did you also try a FDCIM reset from the spanner menu?

I dont get a blue screen, its black with the error message.
I did not change any other fcdim settings.
I did not do an fcdim reset - is this required?



Sent from my EML-L29 using Tapatalk

You are saying when you put in in reverse the screen goes black and has an error message displayed?

saeb wrote:You are saying when you put in in reverse the screen goes black and has an error message displayed?

Will send pic later as well as APIM FCDIM and BCM.

Sent from my EML-L29 using Tapatalk

saeb wrote:You are saying when you put in in reverse the screen goes black and has an error message displayed?

Attached is the error message. I did a reset via the wrench and even via the menu. Still I get the error message.

Here are other info that might help as qell as their as built values.

Interface:
Type: FTDI #1:A73XNJZ7, 2000000 kbps
Adapter: STN1170 v3.3.1 (ELM327 v1.3a)
Min.delay: 16 ms ( Good)
Errors: None

Vehicle:
Model: Ford Ranger/Courier/Mazda B-Series
Engine: Duratorq Turbo Diesel Common Rail Injection
Capacity: 2.2L
Year: 2019
Generation: 2015 MY
Fuel: Diesel
Transmission gear: Automatic

APIM - Accessory Protocol Interface Module
Part number: E6BT-14D212-TB
Strategy : E1BT-14D205-AJ
(54-PIN APIM not 12-PIN)

7D0-01-01 1507 0940 0240


BdyCM - Body Control Module
Part number: JU5T-14B476-DAK (latest known: JU5T-14B476-DAR)
Strategy : JU5T-14C184-AAJ

726-39-02 0000 0000 0068


FCDIM - Front Control/Display Interface Module
Part number: HB3T-18B955-CB
Strategy : E1GT-14D358-CL
(4" screen)

7A5-01-01 00AD 048A 9079

Sent from my EML-L29 using Tapatalk

So its plausible it is not see a video input, whether this be the supplied loom or the camera itself. Test the camera on another device that supports RCA input, a TV for instance to confirm it is working. Apart from this your asbuilt looks ok.

I do not have a FDCIM sitting around to do any testing on so cannot confirm that or not.

saeb wrote:So its plausible it is not see a video input, whether this be the supplied loom or the camera itself. Test the camera on another device that supports RCA input, a TV for instance to confirm it is working. Apart from this your asbuilt looks ok.

I do not have a FDCIM sitting around to do any testing on so cannot confirm that or not.

I suspect the RCA cable is problematic. I tested another camera im getting the same result, will see how it goes when I get another one, should have tested all before installing.

Sent from my EML-L29 using Tapatalk