Ranger Mods

saeb wrote: ↑Thu Jul 20, 2023 5:33 am First DTC is because you enabled mode on the terrain gauge which does not exist on your vehicle.

Without knowing where you are with your current asbuilt I cannot give you the changes for the position circuits. Show block 726-24 and 726-47

Lastly you do not no how to correct CS so it was recalculated for you.

Sorry what's 'cs' mean?
Yeah, the first photo I wasn't meant to upload, Ive changed that back to 'disabled' since.
I'll upload photos of the requested blocks when I'm home later. Cheers

checksum

saeb wrote: ↑Thu Jul 20, 2023 5:33 am First DTC is because you enabled mode on the terrain gauge which does not exist on your vehicle.

Without knowing where you are with your current asbuilt I cannot give you the changes for the position circuits. Show block 726-24 and 726-47

Lastly you do not no how to correct CS so it was recalculated for you.

I've attached blocks as requested;(

726-24-01 0001-00F0-51xx Disable RF Position Lamp Circuit DTC & LF Position Lamp Circuit DTC
726-47-01 0000-0100-01xx Disable Position Lamp Open DTC

xx leave as is accept invalid CS.

This is specific to your vehicle based on your existing AB.

saeb wrote: ↑Sun Jul 23, 2023 4:19 pm 726-24-01 0001-00F0-51xx Disable RF Position Lamp Circuit DTC & LF Position Lamp Circuit DTC
726-47-01 0000-0100-01xx Disable Position Lamp Open DTC

xx leave as is accept invalid CS.

This is specific to your vehicle based on your existing AB.

Yeah cheers Stewart, I'll give that a go tonight.

saeb wrote: ↑Sun Jul 23, 2023 4:19 pm 726-24-01 0001-00F0-51xx Disable RF Position Lamp Circuit DTC & LF Position Lamp Circuit DTC
726-47-01 0000-0100-01xx Disable Position Lamp Open DTC

xx leave as is accept invalid CS.

This is specific to your vehicle based on your existing AB.

I tried these with no luck, the drls come on for ABT 2 seconds then switch to lowbeam.
When you say accept invalid CS how? It just comes up with cancel or ok, if I cancel it doesn't make the changes I'm after, if I continue it changes the CS (same in both these blocks) I did a test on BCM and it showed a similar dtc as before. I've got photos below of the original CS before it changed them and the warning it shows.
Cheers
I'VE ADDED PIC OF OTHER CODE (MISSED IT)

Only reason they would switch to low beam is if it is too dark. I will assume that the headlights have auto position and do come on automatically when the light level drops?

saeb wrote: ↑Mon Jul 31, 2023 2:45 pm Only reason they would switch to low beam is if it is too dark. I will assume that the headlights have auto position and do come on automatically when the light level drops?

Yes, headlight switch is in auto. It seems to think it needs headlights, as Ive stated earlier, you turn ignition on with lights on auto, drls come on for ABT 2 seconds, then switches to lowbeam headlights, doesn't matter how sunny or bright it is that's what it does. All the other light sensors for the cluster and headunit work when in low light/ auto high beams kick in when it's dark so I'm really not sure.

Based off the codes I'd assume the BCM doesn't like it and is turning them off because there's possibly a fault? Think of taking to an auto elec to get another eye over the wiring if i get time;)

It's been a long time since I've posted in here regarding my DRLs on 2021.75 ranger xls. I've had no luck other than there being no DTC present for headlight circuit anymore. The DRLs stills come on for the 2 or so seconds when ignition is turned on and/or the light knob is in the auto position. I took it to my local auto elec today and he checked all my work, checked for power at the DRLs and check what current they were drawing (ONLY MILLIAMPS AS EXPECTED). He said everything I've done looked good. The only thing he could think of was wether the BCM is actually different to a premium pack ranger (eg Wildtrak)