Ranger Mods

Thanks! I was just confirming as it looked like it was for a non ranger

I can confirm that this also works on the MY19.75 Everest Titaniam. Can the Auto unlock feature be changed though? The manual says:
Autounlock unlocks all the doors when:
Your vehicle comes to a stop and you switch the ignition off or to the accessory position.
You open the driver door within 10 minutes of switching the ignition off or to accessory.

The doors on the Everest are unlocking when I open the drivers door but not when I turn the ignition off. Any ideas what can be done (if anything) to enable this?

Possibly, I have not looked further into it due to not owning a MY19+ so would need to spend a bit of time going through everything to sort.

At his point in time I do not have that much time.

No problems, thought I'd ask just in case someone knew. Thanks heaps for the autolock feature either way!!

Wazsxr wrote: ↑Sun Jul 28, 2019 8:45 pm No problems, thought I'd ask just in case someone knew. Thanks heaps for the autolock feature either way!!

Check

BCM 726-16-01
if it is 0202-0202-02xx

Then change it to 0101-0101-01xx

and let me know the outcome.

Thanks Stewart, looks like it's already set to the 0101-0101-01xx:
-Warren

I see no other options at this stage, unless I missed something.

No problems, perhaps not something available on this model. Thanks for trying though!

When typing the new code, x1x1 etc. Does the x mean leave the existing numbers and only update the numbers after x or replace all existing numbers with the full x1x1-x1x1-x1xx code?

I’m keen on the feature as well are there any updates on this.
Thanks in advance.

2point0PX3 wrote: ↑Thu Aug 08, 2019 7:05 pm When typing the new code, x1x1 etc. Does the x mean leave the existing numbers and only update the numbers after x or replace all existing numbers with the full x1x1-x1x1-x1xx code?

Leave the 'x' at whatever it is and ONLY change to the numbers shown.

Wal4x4 wrote: ↑Sun Aug 11, 2019 12:10 pm I’m keen on the feature as well are there any updates on this.
Thanks in advance.

Last post previous page, the changes are listed in full.

Confirming this works 100% on my Wildtrak MY19.75 Bi-Turbo.

Just back up the original items BCM and IPC as built first save it someplace and go for it.

Big thank you to Stewart.

I just did this change my19 everest and it worked for me.
Thanks Stewart!

Can confirm it is now working on my new PX3 XLT BiTurbo

Stewart,
Just on this -- 2017 PX2 Wildtrak, -- can the mirrors be set to turn "in" on ignition off and "out" on ignition on ??
I'm always forgetting to push the little button to turn them in when I've parked mine. The only other time I turn them in is when I'm in the bush and I don't want to foul them on shrubs and close hanging branches.

Iainboyd wrote: ↑Mon Mar 02, 2020 9:37 am Stewart,
Just on this -- 2017 PX2 Wildtrak, -- can the mirrors be set to turn "in" on ignition off and "out" on ignition on ??
I'm always forgetting to push the little button to turn them in when I've parked mine. The only other time I turn them in is when I'm in the bush and I don't want to foul them on shrubs and close hanging branches.

No, they are not wired to any modules and are manual only.

There is a add on module listed in the shop, banner above, from Track Electronics that will what you require. Works on lock, unlock vehicle.

saeb wrote: ↑Sat Jun 08, 2019 3:01 pm

Snappa wrote: ↑Fri Jun 07, 2019 4:54 pm So are we saying that the Ranger Wildltrak PX3 is not capable of coding to do the Auto Lock as it has removed it from the actual firmware?

As per my response above, change the below and it will be available.

Auto Lock

Change;

BCM
726-15-01 to x1x1-x1x1-x1xx
726-21-01 to xxx1-xxxx-xxxx

and

IPC
720-01-01 to xxxF-xxxx-xxxx


Do an ignition cycle and it should be able to be changed.

OK, so I've done this and I get a menu to be able to change it. I can confirm that it works, when I drive off, all the doors auto lock. I also seem to have gained an auto high beam selection that is greyed out, don't know how I've done this as I didn't change anything else (this time). The IPC used to be xxxA-xxx-xxxx and I changed it to xxxF-xxx-xxxx as per the above.

edited due to me not doing it correct the first time around

Doing a bit more research on this. Other model fords require the IPC 720-01-01 xxx!-xxxx-xxxx (! being the number to change) to be increased by 1 to enable the auto lock feature and add 2 to enable to auto high beam feature. As per the above I changed it from A to F, meaning I added 5. Nothing else has appeared on the screen, but I dit get both auto lock and auto high beam, so that's odd.

I have now changed 720-01-01 xxx!-xxxx-xxxx to B, meaning I added 1 from the original number and I can confirm that the auto lock option is available and the auto high beam option is gone.

Was not aware an Australia delivered PX3 did not have auto high beams. I find this odd.

I don't have the tech pack

Yes B is correct in your case then.

Evert, what year is your PX3?

My XLS MY19.75 has Auto High Beam, yes it has tech pack but this only brings it to the Standard XLT Level so would have thought it would of came with it.

saeb wrote: ↑Sat Jun 08, 2019 3:01 pm

Snappa wrote: ↑Fri Jun 07, 2019 4:54 pm So are we saying that the Ranger Wildltrak PX3 is not capable of coding to do the Auto Lock as it has removed it from the actual firmware?

As per my response above, change the below and it will be available.

Auto Lock

Change;

BCM
726-15-01 to x1x1-x1x1-x1xx
726-21-01 to xxx1-xxxx-xxxx

and

IPC
720-01-01 to xxxF-xxxx-xxxx


Do an ignition cycle and it should be able to be changed.

Saeb, does this give me an option in the menu allowing me to turn it on or off by choice? or does this stay on and need Forscan to change back later?

@TieNN89 it’s a 2018 PX3. I don’t have the forward camera as I don’t have the tech pack.

The BCM codes enable the feature to work and the IPC code enables the option in the dash in the setting menu to turn this on or off.