Page 2 of 2
Re: AdBlue tank level.
Posted: Mon Jun 24, 2019 8:11 am
by saeb
Being it is an 18 litre tank and the fill can be good for 10,000 to 16,000 I could not see how it would be even close to 8 litres, hence no movement.
Not sure your sums would really work. 8.09 would be about 40% full which approx where the first sensor is.
Re: AdBlue tank level.
Posted: Mon Jun 24, 2019 11:47 am
by Brett_32i
ill just multiply the original formula by 12.36 to get it to % units.
8.09 * 12.36 = 100%
3 * 12.36 = 37%
etc
it will still only step down % as it comes off each sensor, but to me that means more than the gauge showing 8.09.
Re: AdBlue tank level.
Posted: Mon Jul 01, 2019 5:31 pm
by glockss
I tested this over a longer drive (6k km). Now first of i have PX2 MY16, dealership says it is 20l AdBlue tank. I have previosly run it almost dry once (AdBlue warning with topup requered, less then 50km left warning on the cluster) And i filled 19.2L from the pump. Anyway, when using formula provided i will always get 12.2 MAX. When it did finally started dropping after 2k, it dropped from 12.2 to 11.5 in 108km. I then topped it up, and it took 8.22 liters.
Have i set it up wrong, or is it just for Everest, or do you guys have different sensors?
Im using TorquePro App
Also, AdBlue usage is for me erratic, sometimes i get 6-7k before i need to fill 10-12 liters, sometimes its just 2k. It could be combination of temp. Usually its high consumption during winter, and lower with higher temps
Re: AdBlue tank level.
Posted: Tue Jul 02, 2019 8:46 pm
by saeb
glockss wrote: ↑Mon Jul 01, 2019 5:31 pm
I tested this over a longer drive (6k km). Now first of i have PX2 MY16, dealership says it is 20l AdBlue tank. I have previosly run it almost dry once (AdBlue warning with topup requered, less then 50km left warning on the cluster) And i filled 19.2L from the pump. Anyway, when using formula provided i will always get 12.2 MAX. When it did finally started dropping after 2k, it dropped from 12.2 to 11.5 in 108km. I then topped it up, and it took 8.22 liters.
Have i set it up wrong, or is it just for Everest, or do you guys have different sensors?
Im using TorquePro App
Also, AdBlue usage is for me erratic, sometimes i get 6-7k before i need to fill 10-12 liters, sometimes its just 2k. It could be combination of temp. Usually its high consumption during winter, and lower with higher temps
Only Everests have adblue in Aus, not Rangers. Sensors, tank size maybe an unknown. Not owing an Everest I cannot give anymore input.
Re: AdBlue tank level.
Posted: Wed May 19, 2021 7:33 am
by Wapehawima
saeb wrote: ↑Sat Jun 08, 2019 2:55 pm
Wotto wrote: ↑Thu Jun 06, 2019 1:25 pm
I just added this PID into torque and in my MY19 Everest, I get a result of -0.3. I'm guessing this PID isnt compatible with the MY19, but can someone else confirm incase I've stuffed up? Cheers
Assuming it is entered 100% correct and it does not work then the PID would be different. Different sensors etc also.
I currently do not have an MY19 Everest to pull PIDs from so cannot give you anything at the moment.
Hi Stewart,
Any advance on the adblue level for post MY19 Everest?
I have a 20.75 Sport and mine too shows -0.3. Never changes.
Thanks, Wayne
Re: AdBlue tank level.
Posted: Tue Jun 08, 2021 8:36 am
by saeb