Trying to enable the keyboard so that a passanger can enter in destinations on the sat nave on 2018 ranger with v3 of sync 3. I tried enabling ability to change address in motion but didnt work. Then tried enabling navigation system. Still nothing. Am i missing something.
I have changed both back but now im getting navigation system failure on the dash. Is there something im missing here? Or do these features not change that.
Our everest with v2 sync 3 can use the keyboard while driving and enter destinations etc. Ranger newer with v3 sync 3 has a shaded out keyboard and can only speak a new destination with voice command.
Thanks
Dan
Information: Following the announcement on October 23, 2023, this site has been archived as of July 1, 2024. For further details, visit this page.
Keyboard in sat nav 2018 ranger
- saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
You would be best to start here viewtopic.php?f=12&t=7&start=125 I have a how to fix about half way down. You may be best to start reading from the page before.
Also has your Sync3 been connected to wifi since you made changes?
Worst case, if you PM me your VIN and your saved asbuilt abt file for the APIM in Forscan I will amend and send it back for you to reload.
Also has your Sync3 been connected to wifi since you made changes?
Worst case, if you PM me your VIN and your saved asbuilt abt file for the APIM in Forscan I will amend and send it back for you to reload.
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic
- saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
I have just put another request through for these options to be removed from Forscan as a matter of urgency.
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic
- saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
Good. As above pm your vin and saved asbuilt apim abt file if you have dramas.
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic
-
- Junior Member
- Posts: 6
- Joined: Sat Feb 24, 2018 4:25 pm
- Location: Qld
- Model Of Vehicle: EVEREST TREND UA
- Year Of Vehicle: 2017
- Been thanked: 1 time
Hi stuart
All good got it working again. Couldnt get into asbuilt section of ford website for some reason but just did it manually and all ok now. Just had to wait a bit with key off for new settings to load. Once that was done sat nav back up and running.
Thanks again for the help.
Regards
Dan
All good got it working again. Couldnt get into asbuilt section of ford website for some reason but just did it manually and all ok now. Just had to wait a bit with key off for new settings to load. Once that was done sat nav back up and running.
Thanks again for the help.
Regards
Dan
Ford Everest Trend
- saeb
- Site Admin
- Posts: 4169
- Joined: Wed May 17, 2017 8:50 pm
- Location: Seaford VIC
- Model Of Vehicle: RANGER XLT PX2
- Year Of Vehicle: 2015
- Forscan Dongle Type: Ford VCM
- Has thanked: 295 times
- Been thanked: 1063 times
An update for Forscan soon should see users selecting whether they have a Sync2 or Sync3 with a warning attached.
Stewart
Ford PX2 Supercab 2015 Automatic
Ford PX2 Supercab 2015 Automatic