Bala1 wrote: ↑Sat Jan 14, 2023 6:09 pm
I dont know if the egr fault will cause the spanner warning, but it is in the PCM faults list and probably should be fixed anyway.
There are a lot of faults with possible causes as short or open circuit. It would be worth check all battery cables and earths. There may be a common cause for those,
I’ll have a look around, thanks.
I think most of those are missing modules. Since my Ranger is an XL, but I’ve got Sync 3 and the dual screen IPC, they are probably both expecting a lot of stuff that was the car they came out of. I’ll have to work with the forums here to disable as much as I can to get rid of those codes, assuming they aren’t because of a bad earth.
Here is the breakdown of the codes that I have and what I think is the reason why. Hopefully Saeb see's this and can impose his wisdom.
===PCM DTC P0671:00-6C===
Code: P0671 - Cylinder 1 Glow Plug Circuit / Open
Module: Powertrain Control Module
Unsure
===PCM DTC P0672:00-6C===
Code: P0672 - Cylinder 2 Glow Plug Circuit / Open
Module: Powertrain Control Module
Unsure
===PCM DTC P0673:00-6C===
Code: P0673 - Cylinder 3 Glow Plug Circuit / Open
Module: Powertrain Control Module
Unsure
===PCM DTC P0674:00-6C===
Code: P0674 - Cylinder 4 Glow Plug Circuit / Open
Module: Powertrain Control Module
Unsure
===PCM DTC P040D:00-2C===
Code: P040D - EGR Temperature Sensor A Circuit High
Module: Powertrain Control Module
I think this is the cause of my Spanner warning. Going to buy the sensor on Monday anyway since its not that expensive and I need to be ready for Friday.
===APIM DTC B119F:13-0B===
Code: B119F - GPS Antenna
Module: Accessory Protocol Interface Module
I assume this is related to me having upgraded to Sync 3
===APIM DTC U0159:00-0B===
Code: U0159 - Lost Communication With Parking Assist Control Module A
Module: Accessory Protocol Interface Module
My car does not have sensors
===BdyCM DTC B12C2:15-48===
Code: B12C2 - Puddle Lamp
Module: Body Control Module
My car does not have the puddle lamps
===FCIM DTC B105A:14-0A===
Code: B105A - Cabin Temperature Sensor Fan
Module: Front Controls Interface Module
I assume this is due to Sync 3 upgrade
===FCIM DTC B11E5:15-0A===
Code: B11E5 - Left HVAC Damper Position Sensor
Module: Front Controls Interface Module
I assume this is due to Sync 3 upgrade
===FCIM DTC B1A61:15-0A===
Code: B1A61 - Cabin Temperature Sensor
Module: Front Controls Interface Module
I assume this is due to Sync 3 upgrade
===FCIM DTC B1A63:15-0A===
Code: B1A63 - Right Solar Sensor
Module: Front Controls Interface Module
I assume this is due to Sync 3 upgrade
===FCIM DTC B1A64:15-0A===
Code: B1A64 - Left Solar Sensor
Module: Front Controls Interface Module
I assume this is due to Sync 3 upgrade
===TRM DTC B1488:08-2F===
Code: B1488 - Retractable Tow Bar System
Module: Trailer Module
My car does not have this
===TRM DTC U0121:00-2F===
Code: U0121 - Lost Communication With Anti-Lock Brake System (ABS) Control Module A
Module: Trailer Module
I don't believe my car has this
===TRM DTC U2100:00-2F===
Code: U2100 - Initial Configuration Not Complete
Module: Trailer Module
If this is talking about Trailer Module, I don't think I have this
===IPC DTC U023A:00-0A===
Code: U023A - Lost Communication With Image Processing Module A
Module: Instrument Panel Control Module
Not sure exactly what this is talking about, my cluster has been swapped to the Dual Screen version, perhaps that is the problem?